You will need to buy a 3.5mm ended to a RCA stereo cable from an electronics store. Hook up via the audio 3.5mm out to the receiver audio in.

Probably. Any wireless receiver supporting the industry standard 802.11b or 802.11g protocols should work. However, in rare cases, we have found wireless receivers which had compatibility issues with the computer upon which it was installed. See similar questions...

To connect a turntable to any NAD unit, (with the exception of the 160/162) you will need a phono pre-amp, our PP2. The PP2 phono pre-amp is a simple and inexpensive way to add high-performance phono capability to a pre-amp or integrated amp with spare line input. With the PP2, all turntables are made compatible with the amps. There are two different types of turntables: moving coil and moving magnet. You have to know what type you're buying, and set the PP2 accordingly. See similar questions...

A USB cable and the presence of USB connections are not yet adequate for exchanging data successfully. However, data transfer can be effected using a USB cable if a serial COM Port is emulated by the GPS receiver. The GPS data must be available in the NMEA 0183 format when data is called up online, so that Geogrid is in a position to evaluate these data. See similar questions...

Navtex receivers can be connected to NaviGator. Again they need to have the following pin connections: Pin 2 - NMEA / Position In, Pin 3 - NMEA / Position Out, Pin 5 - Ground. Once it is connected and messages are being received and they have a Lat and Long, they will be displayed on the chart for you to click on and view the message. See similar questions...

We provide an installation manual with step-by-step instructions. FSL equipment is designed for a wide range of interfaces and relays. For special applications, FSL can provide special interfaces. See similar questions...

To connect the audio output from the computer to the AV receiver, you need a stereo mini-plug to a stereo RCA pin cord. Then connect the line-out from the computer sound card to an available audio input on the receiver. Select the input and adjust the volume output from the receiver. See similar questions...

Easy, all you need is a cord that is has two RCA connectors on one side and an 1/8th inch jack on the other. You can buy one at Radio Shack. You can get the fancy one that says it is for iPods for $30, or one that does the same thing but does not say iPod on it for $6 bucks. See similar questions...

The iPod is able to connect to a Windows Computer via a USB2.0 port. Only the iPod shuffle is able to connect using USB 1.1. The iPod nano and the larger iPods require USB 2.0. All iPods ship standard with a USB 2.0 cable. See similar questions...

The phone line connected to your receiver(s) ensures your ability to purchase Pay-Per-View movies and events . It is also required so your receiver's may be updated with the latest software. If you do not have a phone line, there will be an additional $5 per month charge per receiver. The DISH antenna is 20 inches and complies with the Satellite Consumer Bill of Rights, a regulation released by the FCC on August 6, 1996. See similar questions...

No. A DA1920SX transmitter requires a DA1921SX receiver, and a DA1931CT receiver connects to a DA1930CT transmitter only. The main reason is how the video signals are encoded in the transmitter. DA1930CT + DA1931CT provide superior encoding algorithm and signal quality for video transmission. See similar questions...

This allows the cable from the computer or charging source to plug directly into the iPod, or into the Dock, whichever is more convenient. No the iPod and it's iTunes software requires Windows 2000 or Windows XP. The iPod of course also works with the entire Apple Macintosh range. See similar questions...

To connect an iPod with a dock connector insert the dock adapter that fits your iPod, and then connect your iPod. Your iPod Hi-Fi includes dock adapters that work with most models of iPod with dock connectors. If you want to connect another iPod, you can easily remove the dock adapter from your iPod Hi-Fi using a fingernail, insert the adapter that fits the other iPod, and then insert the other iPod. See similar questions...

The wax strip was not applied immediately after wax application and rubbed firmly for 3-4 seconds in the direction of hair growth. For better wax adhesion, lightly dust the area with talcum powder to absorb any excess oil or moisture on the skin before eplilation. Slight irritation is normal after any waxing session, but swollen, discolored or irritated skin could be the result of poor technique. When pulling off the wax strip, hold the skin taut and pull the wax strip off parallel to the skin. See similar questions...

Easy! If your iPod is still covered by Apple's Limited Warranty for iPod or APP for iPod, complete the iPod service request form on our website. Once we receive your service request, we will send you a shipping box including a prepaid preaddressed return shipping label so you can send your iPod to us. Important information about preparing your shipment and the carrier to be used will be included with your shipping box. Please note: a physical address is required. See similar questions...

The speakers incorporate the Direct/Reflecting technology that not only ensures you get a stereo sound throughout the listening area and not just the sweet spot as in the case of conventional speakers, but also deliver a richer and lifelike performance. The Acoustimass technology helps deliver rich pure bass with no audible distortion. See similar questions...

Many new PCs (especially laptops) have USB ports but do not have the standard 9-pin serial ports found on older computers. This presents a problem because most of the GPS manufacturers don't make data cables that terminate with USB plugs. Unfortunately, we have noticed that the USB-Serial converters often cause computer crashes. We are working hard to resolve this problem. See similar questions...

While the Co Pilot will operate with nearly any current radio system without requiring any other peripheral items, there is one exception. Certain current model Futaba PCM receivers and possibly a few JR models may experience interface problems with the Co Pilot. Here's why: some current model PCM receiver output servo data to the servos in parallel (at the same time). See similar questions...

The receiver will have an HDMI connector (High Definition Multimedia Interface) as its primary means of connecting to an HD display. HDMI can also be connected to DVI equipped displays using a suitable adapter cable. Most HDTV content will be protected by HDCP (High-bandwidth Digital Content Protection). This means most HDTV content will only be able to be viewed on display devices that have HDCP software built into them. See similar questions...