For the basic principles read the paper titled "Programmable appliance controls" available on my publications page. Sorry, I can not help you. I obtained the details for accessing the HP-100LX ports under a non disclosure agreement from HP; I do not have any information for other computers. To obtain the information for programming the HP-100LX contact Hewlett Packard and ask for the software development kit. Yes; no; no; no; no. Sorry if I sound negative.

The Music Player does not provide any IR inputs. However, it is possible to provide IR control of a Music Player indirectly through an external control system such as those offered by Crestron or AMX. See similar questions...

Infrared is the only remote control available, since radio frequency is not designed to adequately control the tilt function. See similar questions...

The easiest analogy to make concerning user operation, is that radio frequency is like a garage door operator, where you don’t point the transmitter; while infrared is like a TV or VCR, where you point the transmitter at the device to be controlled. The other major difference is that radio frequency control is sequential, where the user repeatedly presses a single button on the transmitter, going through all possible operations (open-stop-close) until the desired operation is achieved. See similar questions...

There are actually two boxes for the radio frequency system (note that on Model 9600, all remote components are concealed within the head rail): 1. receiver - 4.75”x3.5”x1.5” 2. relay - 3.25”x2”x1.5”. For the infrared remote, the single receiver enclosure measures 4.5”x2.5”x1.25”. See similar questions...

That depends on the classes you are using. In general it requires replacing references to the Internet Explorer CLSID with the Mozilla one. MFC & ATL provide classes for using the IE control, you may have to make duplicate these classes, making your implementation reference the Mozilla CLSID. See similar questions...

Good try, but NO! It would not only control your robot but the other team's as well. It also violates the AUTONOMY rule and the spirit of FLL. A remote has benefits during testing in the pit area, but should be left there. Do not even bring it into the competition area. Remotes make referees very nervous. Nervous referees may confiscate the remote for the rest of the competition. No. You cannot come to the table with your own team's objects all built into a container and use that instead. See similar questions...

No. When you move the mouse while the consultant has control it will counter the mouse movements and inputs of the consultant. It means that we have consultants on duty but they are all assisting someone else at that moment, you can wait and the next available consultant will get to you. See similar questions...

The First, run the remote control server on the remote PC. Next, run COOL! Remote Control on your own PC. Finally, click the "connect to..." menu and input the remote PC's IP address in the connection dialog, and now you are ready!!! See similar questions...

Yes and no. Outdoor models are designed for well ventilated places. Well ventilated does not mean you have a bit of a draft under a crack in the door. In a garage with a window or garage door open, yes you can safely use any of the 12-IR -> 24-IR range of heaters The DESA range of infra-red heaters is the way to go for indoor infra-red heat. These units are designed for indoor use and have safety mechanisms built in to protect you. See similar questions...

No. The EthIR LAN system was developed with the view of implemented the infrared hardware technology on your notebook or handheld computer without the need of a PCMCIA card. Such cards are expensive and drain the computer of power whereas the infrared port uses only minimal power. Also, there could be conflicts when both infrared and PCMCIA cards contend for the same IRQ resources on a notebook. See similar questions...

The simplest is to use two wireless modems: one that is connected to the AX2550's serial port and the other connected to a PC, laptop or single board microcomputer. It will be necessary to write a program on the computer side that converts commands received from a joystick to RS232 commands that will be sent to the controller via the wireless modem. See similar questions...

Sometimes an infrared port may be so well integrated into the casing of the notebook that it may be difficult to tell that a port even exists on the notebook. Look for a square or oval aperture usually on the rear sides or center panel. Some manufacturers place the port on either the left or right side panel and others may even have two ports -- one on the rear and one of the front of the notebook. Consult your manufacturer's documentation for the location of the infrared port on your device. See similar questions...

There are numerous programs available for using your HP48's IR port as a remote control. However, the level of support depends on the particular unit you wish to control. The HP48 is capable of reproducing many of the IR controls of many popular brands of appliances. However, some remotes run at speeds that the HP48 is unable to reproduce. Due to their faster processor speed, the G/GX calculators are able to support more remote controls but are still limited in some cases. See similar questions...

These OneForAll remote control can be used to replace the Sigmatek PVR-800/820 remote control too using the manufacturer code from AKI. With the code 0490 (thanks to Olivier Fischer) it does not work well, but you can programmatically set some keys to make them working with your PVR-800. You can send too the remote control to OneForAll support to let them create a new code for this specific Sigmatek remote control. See similar questions...

We recommend immediately replacing the original battery with a new fresh one. Size A23 12v 33 mAh Alkaline battery. Alternate part numbers: MN21 / E23A / K23A / V23GA / GP23A / 23A / 23GA / A23 / GP-23A / L1028 / LR23A / MS21 / V23 / VR23. These are sold by all major battery vendors (Eveready, Duracell, etc). We also carry this battery on our website. See similar questions...

Port 3389 is the only port you need to open. Windows will attempt to stream sound through User Datagram Protocol (UDP) first. If no port is available for UDP, sound will stream through a virtual channel in Remote Desktop Protocol, which uses port 3389. See similar questions...

If you download the 'Batch file to turn on the MediaMVP user interface on your PC', located here in the MediaMVP support page, you will be able to control the MediaMVP from the host PC without using the remote. This batch file will turn on the MediaMVP user interface on your PC. Once turned on, the Host PC's Monitor will display a mirror of what you see on your TV set with the MediaMVP. See similar questions...