No, not without proper surface preparation. Recommendation is to clean surface and remove previous finish, usually by use of a pressure washer or sanding.

Yes, provided the previous finish has sufficiently weathered to allow penetration of UV Plus for Pressure Treated Wood. For best results, clean the surface with Wood & Deck Cleaner, or sand to a new surface. See similar questions...

I prefer to use a large brush or a mop. You want to get large amounts of Stain Solver liquid on the deck surface. Hand pump sprayers often apply too little solution to the surface. If you must use a sprayer, make sure the product has dissolved completely or you will clog the nozzle! Also, be sure you spray on lots of liquid. See similar questions...

If the surface is hot to the touch, it is probably too hot to apply Penofin wood stain. Do not apply Penofin wood stain in direct sunlight. Product can flash and dry on the surface without penetrating. See similar questions...

You should certainly protect your deck from unnecessary moisture intrusion and the harmful effects of the sun's ultra-violet rays. Use of a penetrating stain, containing water repellant ingredients in most cases will protect your deck best. The pigment in the stain will absorb the ultra-violet rays from the sun and protect the wood fibers from degradation. In most cases a stain will need maintenance every 2-4 years while clear sealers require maintenance every 1-2 years. See similar questions...

Wood products for construction are typically treated in a factory, using a pressure process. The product is loaded into a vessel, then the vessel is filled with a water solution containing the preservative chemicals. The vessel is pressurised to force the solution into the wood. Most dimension lumber can be treated this way, as well as plywood and Parallam. Other composite products are hard to pressure-treat, for example, OSB, LVL and glulam. See similar questions...

Yes. You would need to send us a sample (on wood) of the color that you would like to match and we will have our finishers formulate a finish for you. We would send you the sample of the finish on the wood that your cabinet would be made from for your approval. There is an up charge for this service. The amount would be determined by the type of finish and the number of steps that it takes to achieve it. See similar questions...

Yes, provided the previous finish has sufficiently weathered to allow penetration of UV Plus. For best results, clean the surface with WD Wood & Deck Renewer, Wood & Deck Cleaner and Brightener, or sand to a new surface. See similar questions...

Yes, provided that the surface is sound and clean. Remove any flaking or peeling previous finishes. Do not apply over freshly stained projects or over coatings with stearates, waxes, silicones or teflon. See similar questions...

Normally BST stain is applied by hand one brick at a time. However, we use several different techniques such as sponging, spraying, etc. to achieve a perfect match. The application process differs for each surface so the most effective technique will be determined on a per job basis. See similar questions...

New powder coating technology has been developed by Dulux to powder coat engineered timber products like MDF board. Known as Dulux Trimatrx®, this unique powder coating is available only through Dulux Registered Applicators for Heat Sensitive Substrates. Dulux have tested many grades of MDF board with Dulux Trimatrx® and most boards provide a good surface for coating. For outstanding results, Dulux recommend Trimatrx® MDF Board in conjunction with the Trimatrx® Powder Coat. See similar questions...

Unlike wood, PVC products keep their good looks year after year with just an occasional rinse with a garden hose. That’s the real beauty. See similar questions...

On a horizontal surface, Penofin may be expected to perform for an average of 9-18 months and 3-5 years on a vertical surface. The time will vary depending on the percentage of sunlight, weather, etc... Yes. All Penofin wood finish colors contain the same ingredients, just different amounts of colored pigments. However, you will not be able to make the surface lighter by applying a lighter shade. As always, you should test a small area before use. See similar questions...

No, "New Wood Defender" is recommended on pressure treated wood, as well as Cedar and Redwood during the first year of weathering. Wood Defender is a latex based product used to stabilize new exterior wood. This product is treated with fungicide to prevent the growth of mildew. See similar questions...

If using a semi-transparent stain, like DEFY, apply only as much stain as the wood can easily absorb and take care to brush out any puddles that may form. If you put enough stain on to form a gloss on the surface, it has been over applied and will, more than likely, in time, peel. The Spring and Fall certainly offer the easiest conditions to work in. See similar questions...

Wool is naturally stain-resistant. We do not have a stain-resistant agent applied. If you wish, you can have a local carpet cleaner apply a stain-resistant treatment. See similar questions...

A film forming coating is a product that does not penetrate into the wood completely. A product that does not penetrate can result in premature peeling and or flaking. All of our wood deck stains will penetrate into the wood when applied properly. See similar questions...

The hair is individually bonded using the latest Ultra Sonic technology. Holly is one of the few in the Mid Atlantic to provide this advanced application technique. See similar questions...

Crystal Clear sealers will not filter out UV rays for very long or at all. A transparent tinted sealer acts like sunglasses for your wood, filtering the UV rays and prolonging discoloration. You can use a clear sealer but it will gray very quickly. See similar questions...