The valve seat gasket inside of the valve may have become worn or loose. If this is the case, you will need to replace the gasket. With the pump off, remove the cover screws of the valve. NOTE: Mark the top and bottom of the valve with a marking pen. It's very important that you do not change the location of the cover when re-assembling. Some newer valves will have a flat spot along side one of the cover screws. When re-assembling, align the flat spots.

Filter - Water flows from the pump to the top of the filter, through the media, out the bottom of the filter and returns to the pool. Backwash - Water flows from the pump to the bottom of the filter, up through the media, out the top of the filter and out the waste line. Rinse - Water flows from the pump to the top of the filter, down through the media, out the bottom of the filter and out the waste line. Winter - Should only be used when the system has been winterized.

No. The cap does not help to keep air in the tires. This cap does serve to keep the valve clean, so you should keep it on.

This document tries to answer questions asked frequently on the mailing list or other questions that people might have when starting out with or evaluating Bricolage. Currently only PostgreSQL support is maintained. There is an Oracle driver, but it's old and not known to work. A port to MySQL 4.1 is reportedly underway.

Under normal conditions, once every 2 weeks. The pressure gauge on your system indicated when backwashing is required. The more dirt trapped in the sand bed of the filter, the higher the pressure will become.

Well a cynic might answer that there are two kinds of roofs, those that leak and those that will leak. Roofs leak from a break in the waterproofing layer, sometimes caused by mechanical damage (ie, someone dropping an HVAC access panel on the roof), sometimes from an opening in the sealant, such as pitch pans and caulking, and sometimes from deterioration or defects in the roofing material. The key roof management task is leak avoidance. Find and correct defects before they leak.

A standard technology engine brake consists of a solenoid valve, control valve, and master and slave pistons. These components are assembled into a housing as shown below. When the brake is activated, the solenoid allows oil to pass to the control valve. The control valve moves up and the check ball in the control valve is unseated, allowing oil to fill the master/slave piston circuit.

The EGR re-routes some of the exhaust gases back into the intake/combustion chamber. This is basically done to reduce emissions. Blocking it off will reduce the temperature of the intake since the gases fed back through the EGR are very hot. Lower intake temperature produces more power, but the amount of gases that are passed through the EGR is VERY minimal and probably won't result in much (if any) performance gain. The drawback is increased emissions.

The most probable cause is that the time clock is not set for the correct time of day. Try checking your clock and reset the time if necessary.

If a gas is escaping or an electrical line is penetrated, the excavator is required to notify emergency personnel, notify the operator, and take reasonable steps to minimize hazards to persons and property until either the operator's personnel or emergency first responders arrive on scene. Examples of reasonable steps would be to keep traffic clear of the area where the damage occurred or to evacuate the public in the area.

Most commonly the cause is a bad spider gasket in the multi-port valve or the entire multiport may be bad. Contact us or service and parts.

The Vortex® Valve is an automatic pressure relief valve that regulates air with changing altitude and temperature, while keeping water out. Storm Case pressure equalization vents (Vortex® valves) are the result of a unique molded housing and a special "Gortex" gas-permeable micro-porous membrane that can repel liquids and micro-particles while allowing gas (air) molecules to pass right through the membrane.

Quite possibly. If you can fill out the valve dimension worksheet in our catalog (see the last page in the GV or BF sections of our catalog) we should be able to fulfill your needs.

Our unique guarantee protects you against breakage of any kind, your fault or ours, for TWO YEARS. Even if you step on a nail or the dog chews them, we will replace them absolutely FREE!

If inserted properly, The Keeper “should” not leak. However, some women find that it does-especially on those first 2 days. If you have a heavy flow or you wear it overnight, you might want some added protection. Or, you may find that you need to empty it slightly more often than you have been. Some women find that (on their heaviest days) it can leak somewhat, if it becomes full and is not emptied soon enough.

We have discussed above how contaminants like wear particles are generated and contribute to increasing formation of sludge and reinous matter. Sludge, being acidic, attacks and reduces life of oil seals. Sludge has an electrochemical attraction to metal surfaces and will deposit on oil coolers, reducing heat transfer efficiency.

The R1100's ooze from a number of places: the oil pressure sending unit on the left front on the engine seeps badly; so do the cam covers on the rear of the cylinder heads. The rear main seal and oil sight glass secrete oil on some bikes. If your rear main seal develops a leak, it can ruin your clutch. BMW will cover this clutch replacement under warranty. There is a small hole on the underside of the engine which is intended to allow oil out of the clutch housing should the rear main seal leak.

The newest pen technology is virtually immune to this problem. However, low cabin pressures can wreak havoc if there is a significant amount of air in the refill. Always try to fly with a full pen.

No. Older meters will not have a leak detector. A leak detector is a small triangular shaped feature visible on the face of the water meter. If the leak detector is moving, while all fixtures, or faucets are shut off, that usually indicates water is being lost somewhere. If the house valve is turned off and the leak detector is moving, that usually indicates that the service line is leaking. (The pipe feeding water to the house from the water meter.)