The operation of a current regulator is similar to that of a voltage regulator. The basic difference is that one regulates current and the other regulates voltage. Voltage regulation for brakes and clutches has limitations because of a change in coil resistance due to heat. Therefore, voltage regulation is not practical for use with electromechanical brakes and clutches.

Current carrying capacity measured in Amps, is the maximum load that this switch will carry with the contacts in a closed position. Current and voltage rating is the tested amperage capacity when you switch the contacts between positions under load when you switch between positions, an electrical arc occurs, Over a period of time, this arc causes contact wear. A switch with the contacts closed has no arc, and carrying capacity is higher.

SAMHSA has worked closely with the Single State Authorities for substance abuse and their partner agencies to build an infrastructure to meet the requirements of the Synar Regulation. As a result, there has been tremendous progress on the part of the States in complying with the new SAPT Block Grant requirements. The Agency is pleased to report that all States (excluding the delayed applicability States) are in compliance with the basic provisions of the SAMHSA Implementing Regulation.

The voltage difference between loaded and unloaded output. To provide the proper secondary load voltage, extra primary windings cause the no-load secondary voltage to be 3-5% higher than the load voltage. Also known as "compensated windings."

Magtorx's Digital Power Supplies (DPS's) are designed for high performance and high accuracy. Magtorx Power Supplies have a current regulation accuracy lower than 1% of full scale range (some models show an accuracy between 1/4 and 1/2% - see Model EC-120 spec.) Yes. Magtorx DPS's provide power and control for torque apparatus. The Programmable DPS allows the user to program and execute the program for white range of applications.

Since brake or clutch torque is proportional to current, a constant current is required to provide steady torque. If voltage were to remain constant, the current would drop as the coil resistance increases, therefore, the brake or clutch torque will drift. As an electromagnetic brake or clutch heats up during normal operation, the resistance of the copper coil can increase up to 25%.

Yes. Magtorx's DPS's can be use for some small DC motors wherever there is a need for torque adjustment. The controlled current range has to stay within limit of the power supply.

Line voltage in the United States is 120 volts. It is the voltage that is supplied to your home or office. Low voltage is less than the supplied voltage. Some lamps, like GE's ConstantColor? Precise? MR16 lamps, run on low voltage. Getting low voltage to lamps requires that the supplied electricity (at 120 V) passes through a transformer to reduce it prior to operating the lamp.

In the US, most of your standard wall electrical outlets are rated at 120 or 130 volts. In order to use SoLux products the power has to go through a transformer to reduce it to 12 volts. Each track fixture and all our other fixtures such as task lamps have a transformer within it to allow it to use the SoLux bulb.

AVR maintains steady voltage. This is important for running sensitive electronics such as computers, microwaves and televisions.

Most of the hotels use 110 or 220 volts, a.c. 60 cycles. Power outlets for shavers and other appliances are a convenience provided in most hotels. A converter/adaptor for other appliances is required.

When a constant current stimulator is used, the stimulator will attempt to deliver the requested current through the stimulation electrode impedance to the limit of the stimulator’s voltage capacity. The maximum voltage that a constant current stimulator can support is termed the compliance voltage. The maximum current that a constant voltage stimulator can supply is the compliance current.

Your current balance is the total amount currently in your account. Available balance is your current balance plus any available overdraft protection funds.

Testing voltage is the maximum 60 Hz voltage that can be applied to the vacuum capacitor without breakdown occurring. Capacitors are tested at this voltage to determine the general condition of the capacitor. Working voltage is the maximum peak voltage that can be applied continually. A complete response to this question can be found in the Jennings TechNote C-2: "The Effects of Voltage on Vacuum Capacitors"

A voltage regulator functions as a voltage converter as well as a voltage stabilizer. A voltage stabilizer will stabilize the electricity to a fixed current. VC model transformers come with a European-to-American plug adapter. You can find additional types of plug adapters on our site.

Absolutely. You will be exposed to AC line power wires while building it, and the filter capacitors store a lot of energy. You must exercise due caution while building it to avoid electrocution. Wall power can kill! This is a do-it-yourself project. That means that all benefits are yours, and all of the responsibility is yours.

Innovative Energies manufactured and most imported products have a 2 year warranty period from date of purchase unless otherwise stated.

The Paracube? and the electrochemical sensor are diffusion devices of comparable size. Both sensors can therefore take advantage of the same, simple sampling system.