If your current receiver has no subwoofer (RCA) line level output, you will need to connect the subwoofer to your receiver using speaker wire connections on the rear of the receiver. You first need to take the speaker input from the subwoofer to the A or B speaker terminals on the rear of the AV receiver. Then take the speaker outputs from the sub woofer and connect to the main speaker terminals inputs.

You typically have two options when connecting a powered sub woofer. Input (1) on the rear of the sub woofer would be used when connecting the sub woofer to the receiver using speaker wires. You would then connect the main speakers to the opposite end, or output or the sub woofer to the main speakers. Option (2) would be using RCA line level output jacks, input (2) on the rear panel of the sub woofer directly to the single sub woofer output on the back of an AV receiver. See similar questions...

No. We do not recommend that you connect anything except the B1 bass module to this output, as the internal amplifier and B1 bass modules are designed to properly equalize the system when connected. Use the Bass Line Out connection to feed a powered subwoofer or additional amplifier. See similar questions...

To connect the audio output from the computer to the AV receiver, you need a stereo mini-plug to a stereo RCA pin cord. Then connect the line-out from the computer sound card to an available audio input on the receiver. Select the input and adjust the volume output from the receiver. See similar questions...

I give a formula in Ref. 2 and in Design Models A1 that relates the sound pressure level from a driver on an open baffle to the SPL from the same driver in an acoustically small closed box, assuming that both have the same cone excursion. frequency Fequal the SPL is the same for either driver arrangement. The open baffle driver output decreases at 6 dB/oct below this frequency relative to the closed box. See similar questions...

In most cases, your TV may only have one set of video inputs. If this is the case then you are limited to the amount of video product that you can connect to the TV. By connecting all your audio/video components directly to the receiver, you would only have to use one video cable from the receiver to the TV. This in turn simplifies the connections, which makes video switching easier. See similar questions...

The phone line connected to your receiver(s) ensures your ability to purchase Pay-Per-View movies and events . It is also required so your receiver's may be updated with the latest software. If you do not have a phone line, there will be an additional $5 per month charge per receiver. The DISH antenna is 20 inches and complies with the Satellite Consumer Bill of Rights, a regulation released by the FCC on August 6, 1996. See similar questions...

The speakers incorporate the Direct/Reflecting technology that not only ensures you get a stereo sound throughout the listening area and not just the sweet spot as in the case of conventional speakers, but also deliver a richer and lifelike performance. The Acoustimass technology helps deliver rich pure bass with no audible distortion. See similar questions...

Probably. Any wireless receiver supporting the industry standard 802.11b or 802.11g protocols should work. However, in rare cases, we have found wireless receivers which had compatibility issues with the computer upon which it was installed. See similar questions...

To get audio from your TV through your AV receiver, please connect stereo audio cables from an available AV input on the rear of your receiversuch as D-TV/LD or CBL/Sat. Then refer to your TV owner's manual for more information about audio output to an amplifier. You may have to turn off the internal TV speakers in order to get any output from the TV into the AV receiver. See similar questions...

A USB cable and the presence of USB connections are not yet adequate for exchanging data successfully. However, data transfer can be effected using a USB cable if a serial COM Port is emulated by the GPS receiver. The GPS data must be available in the NMEA 0183 format when data is called up online, so that Geogrid is in a position to evaluate these data. See similar questions...

Navtex receivers can be connected to NaviGator. Again they need to have the following pin connections: Pin 2 - NMEA / Position In, Pin 3 - NMEA / Position Out, Pin 5 - Ground. Once it is connected and messages are being received and they have a Lat and Long, they will be displayed on the chart for you to click on and view the message. See similar questions...

We provide an installation manual with step-by-step instructions. FSL equipment is designed for a wide range of interfaces and relays. For special applications, FSL can provide special interfaces. See similar questions...

The pre-amp circuitry in each EMG pickup is factory preset for the optimum output level. This level was carefully determined to minimize hum and noise while maximizing a clean output signal under heavy playing and high transients, and can't be modified. See similar questions...

Yes, many Yamaha AV receivers are stable down to, but not below 4 ohms. We recommend that you use only speakers with a minimum of 4 ohms. Also, please make sure that the impedance selector switch is set to the correct position as recommended by the owner's manual. See similar questions...

The external input connections on the rear of the unit are designed for an MPEG2 processor that is very popular in Japan and was scheduled to come to the US. So at this point, there is no US made component that you can connect, short of a 6-channel separate processor that you can use for this port. At the present time, please ignore that section of your AV receiver. Currently, only the RX-Z9 and the RX-797 Stereo receiver are capable of accommodating a graphic equalizer. See similar questions...

When using the transverter ports -- maybe. Even at 0 dBm this presents a challenge, but we may be able to do it with shielding. It may also depend on the bands being used. See similar questions...

of Apache 1.3, CGI scripts are essentially not buffered. Every time your script does a "flush" to output data, that data gets relayed on to the client. Some scripting languages, for example Perl, have their own buffering for output - this can be disabled by setting the $| special variable to 1. Of course this does increase the overall number of packets being transmitted, which can result in a sense of slowness for the end user. Prior to 1. See similar questions...

If your receiver does not do update make sure you are using the property cable (null or Cross over) .If you are using USB cable make sure you define the driver for the USB to com cable. See similar questions...

Third level domains are just like regular domain accounts on our system. They are billed the same monthly charges and get their own control panel and IP number. The only restriction, is the second-level domain (i.e. domain.com) must already be pointed to our servers for the third level domain (i.e. sub.domain.com) to work. See similar questions...