Simple, first do a rough adjustment of length so that your boot snaps in and looks like it's correctly held. Length adjustment is done with the screw at back end of the binding rail. Next, with the boot in the binding, adjust the length screw a few turns in or out so that it's exactly flush with the rear surface of the rail. Take care to get this right. Too much forward pressure may cause the toe unit to break off the binding, while too little will cause pre-release.

The Freeride is sold with brakes, while the Explore/Express is sold without, so we weigh them that way. Note that with brakes, weights of all models are similar. We get all our weights by actually weighing items on a digital postal scale. Weights shown here may differ from other published weights, this could be due to manufacturing changes or publishing errors. If you see something that doesn't look right, please contact us (use contact option on main menu).

Using your randonnee bindings for all your skiing, resort and backcountry, is known as "one rig." The wisdom of using bindings as "one rig" depends on a few factors. If you're primarily doing laps using ski lifts you'll be covering an immense amount of vertical that places wear on the bindings they were not designed for. More, though the Fritschi toe release is adequate, it's not as highly engineered as the latest alpine bindings.

Sorry, not likely. The bar connecting the toe and heel units of all Fritschi backcountry skiing bindings has machined slots near both ends that would end up where you'd cut the bar to make any significant length change.

Yes. If you need Freeride bindings look for them on the used market. Search web forums and Ebay. If you don't need the beef of a Freeride the older Diamir Titanal 3 is a good alternative and may still available on the retail market. T3 is not in production, however, so it's somewhat of an "orphan" product.

Check your tire pressure before you begin traveling. Underinflated tires heat up quickly and can result in tire failures and possible loss of vehicle control. Overinflated tires can cause your tires to wear unevenly. It is also recommended that you carry a spare tire for both your vehicle and your trailer, along with proper tools to change a tire, if necessary.

Adjusting Naxos for your boots is easy, but takes a number of steps. You start by adjusting the length between toe and heel unit, then fine-tune the height of the toe jaw, then set your release numbers. The whole process is detailed here. Ramp angle is the difference in height between your toes and heel when you're standing in your ski boots. It's a ski boot parameter if you're boot is off the ski, and a "stance" parameter once you're clicked into your bindings.

The Naxo NX01 toe and heel can be cranked up to a DIN 12 (with medium and large binding, small binding max DIN is 9). The NX21 goes to DIN 13. Setting 12 is much higher than most skiers will ever use, but is useful if you're skiing terrain where loss of a ski can mean death, or you're jumping off cliffs and trying to ski away from the landing.

No. Since a chiropractic adjustment is a specific force, applied in a specific direction to a specific joint, it is virtually impossible to adjust oneself correctly and accurately. It is possible to turn or bend or twist in certain ways to create a "popping" sound that sometimes accompanies a chiropractic adjustment. Unfortunately, this type of joint manipulation is usually counterproductive, often making an already unstable spine even more unstable, and can sometimes be dangerous.

Since Square D is probably the most popular pressure switch on the market, that's the one we will talk about. The Square D pressure switch and a few other brands that have copied Square D normally have two springs pushing down on a plate supported on top by 3/8" locking nuts. These nuts can be adjusted to set the desired on/off pressure of your pump motor. If you are looking to increase the pressure switch settings, you should first adjust the taller of the two springs.

Yes. You must adjust the set-screw for the maximum static pressure you choose. See the instruction manual for procedure.

On Fri, 15 Sep 95 10:30:56 BST Nick Ing-Simmons <Nick.Ing-Simmons@tiuk.ti.com> writes: Re: Multiple binds to a single widget? ************************************** On Thu, 14 Sep 1995 14:57:54 -0400 Alain St <astdenis@cmc.doe.CA> writes: !In the tcl/tk doc I have, they say that prepending the script !with '+' appends the new binding to the current one.

When a physician orders a pressure change, or a patient moves to an area with a very different altitude and does not have an altitude compensating machine, there are a number of ways to ensure you are receiving CPAP therapy at the correct pressure. Most sleep laboratories and sleep disorder centers are very willing to make this change at no cost. This is routine in most facilities. Just call a big local hospital or ask you physician for sleep lab phone numbers.

Stock settings on the 4th gens are around 43 to 45 psi. The best (adjusted) pressure seems to be variable depending on your cars specific modifications. But even cars with similar mods react differently to pressure adjustments. Some people claim 47 to 49 psi is best, while others find a lower setting like 39 to 42 psi is best. From testing, it seems the computer will adjust itself to a fuel mix level it is comfortable with.

Pressure is the amount of force pushing the flow of water. It's measured in pounds per square inch (PSI) and can be easily measured with a low cost pressure gauge. Knowing your starting pressure helps determine whether or not you need a pressure regulator, but it's not essential in a simple backyard system. Regular household pressure is often around 50 PSI.

Downstream pressures significantly higher than the regulator's pressure setting may damage soft seats and other internal parts.

On Fri, 15 Sep 95 10:30:56 BST Nick Ing-Simmons <Nick.Ing-Simmons@tiuk.ti.com> writes: Re: Multiple binds to a single widget? ************************************** On Thu, 14 Sep 1995 14:57:54 -0400 Alain St <astdenis@cmc.doe.CA> writes: !In the tcl/tk doc I have, they say that prepending the script !with '+' appends the new binding to the current one.

Yes, the Gtk# project provides bindings for Gtk+, Gdk, Atk, libgnome, libgnomecanvas, and libgnomeui. Other libraries under the GNOME framework will be added on an as-needed (and as-requested) basis.