Click GPS->Configure GPS. Select the port and baud rate that fits your GPS connection (serial, CF, or Bluetooth). Most serial cable GPSes use Port 0 (cradle port) and Baud Rate 4800. Some use higher rates. For CF GPSes, check the manufacturer's documentation or contact us at mapadvisor@cox.net and provide your PDA and CF GPS brand and model. Click Start Test. If the settings are correct, incoming data should be displayed in the text box. If not, click Stop Test, change settings, and try again.

Only if you have Sony Clie NX or Sony NZ PDA you have to download and install special driver written by Pelaca. This is a small PRC file. You can download it from here

Answer: Nexia can communicate at a baud rate of 9600, 19200, 38400, 57600 and 115200. Factory default is 38400. To change the baud rate of Nexia, connect to the network with the Nexia software, select Device Maintenance, select the Nexia device you wish to change, and select Serial Port Settings. Choose the appropriate baud rate then select OK.

Answer: Audia can communicate at a baud rate of 9600, 19200, or 38400. Factory default is 38400. To change the baud rate of Audia, connect to the network with the Audia software, select Device Maintenance, select the Audia device you wish to change, select Serial Port Settings. Choose the appropriate baud rate, then select OK.

Baud rate is the number of times a modem's signal changes per second when transmitting data. It is how modem speed is measured. The bigger the number, the faster you can communicate.

There is no method to directly set the baud rate - instead you must set the appropriate combination of bus timing parameters. The baud rate is calculated...

No, not with the stock 18.432MHz crystal that comes on the TINI. CAN requires baud rates to be accurate within 0.5%; unfortunately the 18.432MHz frequency... If you choose the socket board without the regulator (the TINI Sockets E10), you will need to feed your TINI at least 250mA @ 5.00 V +/- 5% In other words,...

It is the measurement of bandwidth (see bandwidth). Measured as the number of electrical oscillations that occur in a second, each oscillation holds one bit of data. The bit rate is usually the same as the baud rate. Older modems measured in baud rates, newer modems measure in kilobits per second.

The UART function contains an internal baud-rate generator. This is controlled using the BRG register and the second bit, BRGH, in the UCR2 register. When BRGH is 0, the baud rate is equal to Fsys/{64*（N+1）} and when BRGH is equal to 1, the baud rate is equal to Fsys/{16*（N+1）}. N has a value between 0 and 255. Question 34

Not necessarily, GPSViewer, Wayviewer, and LocViewer work with almost any factory setting. Nevertheless it is reasonable to let the GPS receiver send exactly the data which are also processed afterwards, in order to not waste the reduceded computing power of the mobile phones. GPSViewer, Wayviewer, and LocViewer are able to process the NMEA 0183 sentences GGA, VTG, and RMC. For GPSViewer and LocViewer it is optimal to send one GGA and one VTG sentence per second (in this order).

If you have a simple stereo soundcard, select in the Audio Configuration panel, the Split mode and the External mixer checkboxes. You will have: deck A on left mono channel and deck B on right mono channel. Buy (if you don't have) a cable with a stereo plug-in at one end (plug it into the soundcard output), and 2 mono plug-ins at the other end (plug them into the mixer's inputs).

Port trunking is connecting two switches with multiple links that act as one high-bandwidth link. Up to four port (full- or half-duplex) can be used for each trunk on a Switch 2000 or Switch 800t. This enables up to 800 Mbps of bandwidth for linking switches. The benefits of port trunking are: The illustration below shows how port trunking is used in three different locations. Initially, all of the links were 100 Mbps links at 100TX speed and in full duplex mode.

You can find instructions for most popular routers at http://www.portforward.com/routers.htm. Try http://www.canyouseeme.org/ to check your port forwarding.

Why don’t genealogists use the simple terms “primary source” and “secondary source?”

Yes, for CR3001, the baud rate is user selectable via DIP switches located inside the cash drawer. The default baud rate setting for CR3001 is 9600 bps, no parity, 8 data bits, 1 stop bit. The baud rate is selectable from 150 bps up to 19.2K bps. The data bits are selectable between 7 and 8 bits string. For CR3002, the drawer is able to work with baud rates from 150 bps up to 19.2K bps automatically. No setting is necessary.

The basic problem is that updating the screen takes too long and some incoming characters are missed. The exact baud rate where characters begin to disappear depends on the configuration of the Kaypro and the terminal program. Generally, the older non-graphic Kaypros will run at a much higher baud rate before characters start to disappear. Stock Kaypros are not interrupt driven and the BIOS ROM has several built-in delays, which demanded too much of a 2x/4x/10's time.