Yes. We recommend annual service of your fireplace by a qualified serviceperson. This will ensure that your appliance is functioning properly. Your decision really comes down to how much a priority heating efficiency is for you. If you want a lot of heat from your fireplace, you should consider a direct vent gas insert. From a cost standpoint, an insert will cost approximately five times the cost of a nice gas log set.

Installation of our hearth products must be done in strict accordance with local or national building codes, and the unit's installation manual. We recommend that our products be installed by a factory-trained Mr. Fireplace installer.

You will need to contact a Mr. Fireplace Sales Representative in your area. Refer to contacts for locations

Yes, but placement is key. Again the fan needs to draw cooler air from behind to operate and the surface on which the Ecofan is placed should never exceed 340ºC (650ºF).

Freestanding stoves can be connected to chimneys built especially for them. The chimneys may be of masonry construction or be a factory-built metal system that's been designed, tested and listed for use with wood burning appliances. Freestanding stoves can also connect to an existing fireplace chimney, if the height and position of the stove's flue collar permits it. When this type of installation is done, the stoves may be called hearth stoves.

Please make sure the flue is open before starting fire. NEVER remove hot ashes or partially burned loges. Please leave the ashes in the fireplace even if you are sure they are cold. It's easier to build a fire with a bed of ashes. If it becomes absolutely necessary to remove the cold ashes, use a metal container only. (Anything flammable, such as a paper bag or cardboard box, even if you are positive the ashes are cold, is extremely dangerous.

Unfortunately, no. You will need a wood pellet stove but if you don’t already have one, the savings you will realize in heating your home will more than pay for the stove. Some companies do offer converters which may be placed in fireplace inserts. Please check with your local hardware store or on the web to see if this option will work for you.

If you already have a brick or stone fireplace, or a factory-built fireplace, and you want to convert it to gas, then the most cost-effective solution is an insert. If you are remodeling a part of your home that never had any kind of built-in structure, then you need a Direct Vent fireplace that does not require an existing opening or chimney.

Yes, we sell Mr. Flame Fireplace Glass Doors which are designed to work with the Fireplace Radiator™. Click here to view them.

Chances are there will be a gap between the insert and the inside of the fireplace. That is why we offer a range of faceplates designed to cover the gap. The faceplate also houses the on/off switch and fan control, so you don't have to crouch or bend down to operate your insert.

EPA Regulations are government regulations of wood burning appliances mandating that products sold after July 1, 1992, emit no more than 4.1 grams of particulate matter per hour for catalytic-equipped units and no more than 7.5 grams for non-catalytic-equipped units. When starting a fire, use plenty of crumpled newspaper and kindling. As a guide, fill the firebox completely with loosely crumpled newspaper and hold it down with at least ten pieces of finely-split dry kindling.

More than likely, yes. We commonly remove birds, rats, squirrels, raccoons and other animals from attics, crawlspaces, stove vents, fireplaces and other locations in homes, garages and sheds.

Carefully open the damper and, using a flashlight, look up the flue for signs of a build-up along the walls. Goggles are suggested for this. If the build-up is ?" or more, a cleaning is needed.

Any tile can be used on the face of a fireplace. I would not recommend putting the tile directly In the firebox.

It is sometimes called a base-page. It is the foundation of the album and is attached to the binding of the cover by pins, hinges, clips and stitching.

The safest installation available for a woodstove insert is one that is lined to the top. Reasons to line a woodstove insert to the top include:

Once a permit has been issued and work has begun, inspections are performed by the City's inspectors at intervals designated by the Florida Building Code. Simply stated, an inspections is required prior to concealing any part of the construction. The building permit that is issued will indicate the types of work that requires inspections and when to call for one. This permit must be displayed on the job site.

im buying a new ac ready furnace for my mobilehome,., i have the paperwork from the previous owners purchase of a new kenmore outside cooling condenser,tech info and so on but it does not say its a 1 ton or3 ton or3.5 ton ,HOW CAN I FIND OUT WHAT TONAGE IT IS SO I GET A PROPERAC READY FURNACE THE FURNACE IM LOOKING AT WILL HANDLE UP TO A 4 TON I am interested in purchasing an Eden PURE portable infared heater, Model 1000, which the internet site states is 5200 BTU.

We have very high standards in our cutting and sewing departments. Our employees are not on a piece rate system. Most inspection is done while sewing the product. An inspection is also done at the final stage of packaging. Working with your concerns on the inspection of your product is important to us.