If you run Virtual Personality and your modem does not support voice, it usually introduces automatically upon startup, some message regarding that. Besides, switching to one of the Telephone output modes should cause telephony buttons like Dial..., Connect, Record and Hangup to become disabled. If voice is supported, some of them will be enabled. Regarding speakerphone modem, look at the rear of your PC.

You can perform several commands in Windows HyperTerminal to make sure. Please refer to the question #3 on how to work with HyperTerminal. If OK, then your modem is definitely a voice modem. Probably it's built with Rockwell, U.S.Robotics or PCTel chipset. If OK, then your modem is definitely a voice modem. Probably it's built with AT&T (Lucent), Rockwell HCF chipset or is a ZyXEL modem. See similar questions...

There must be a way to connect the PC to the telephone lines. This can be done with a voice modem or a voice card. Voice modems provide a low cost solution to this requirement and also provide an inexpensive method of evaluating Phone-In Buddy. Voice cards should be used at sites that require more than two lines for incoming dictation or where higher quality recordings are required. Please contact High Criteria for more details. See similar questions...

You should connect the speaker output of the sound card to the microphone input of the modem with a 3.5 mm double mini jack stereo cable. You may use an output splitter on the sound card, which enables you to maintain the current speaker connection along with the new connection. Refer to the Help for more details. See similar questions...

To ensure the highest quality sound and experience for all participants, calls from speakerphones are NOT permitted. See similar questions...

Yes, you will be able to answer calls, play announcements, pass text strings through a text-to-speech engine, record messages, and detect keypad input. You will not be able to use speech recognition except in a clumsy way because the drivers for voice-modems tend not to allow programs fully duplexed access to the audio streams in a call. See similar questions...

Pick up your DigiPhone handset and listen for a “stutter tone” – a stutter tone indicates that a Voice Mail Message(s) has been left for you. On phones with message waiting indicator/light you will see the light flashes. See similar questions...

The programs that you used before were compliant with analogue modems. You can use programs which are compliant with ISDN applications on your PC and are compatible with netMod. (RVS-COM). B-channel is not working. Your Internet Service Provider (ISP) fails to provide greater rates of data transfer or ISP lines are busy at the moment that the call is made. See similar questions...

A If you have a voice modem and it is properly set up, you may be able to have it recognised by vgetty even if it does not work automatically at first. VOCP now includes a patch to vgetty which creates a new option for voice.conf: force_detect. Instructions for applying the patch are available in the Vgetty:Install section. See similar questions...

In most cases your use of the PS-6155 software should not affect your internal modem. If you experience communication problems between the PC and the organizer and you change settings for your Communications Port (such as the Receive Buffer rate and Transmit Buffer rate), these changes could affect the performance of an internal or external modem, so be sure to return to your original setup after you use the PS-6155 software. See similar questions...

The first place to start may be with the modem manufacturer's Web site. This will require that you first identify the product number and possibly the chipset being used in the modem. See similar questions...

Only modems that contain RPI or RPI+ need to be concerned about using an RPI driver. However, some modems contain both hardware and software (RPI+) error correction and data compression (ECC). To determine if your modem is an RPI modem, before dialing or connecting, use the Windows terminal program and enter AT13 . See similar questions...

We do not recommend speakerphone as it amplifies noise and this may affect the recognition and performance of the system. Speech recognition is a new technology gaining visibility to the general public. Below are some tips on using a speech application: See similar questions...

A cell phone desktop speakerphone is a great office addition. Use wireless desktop speakerphones for conference calls. See similar questions...

No. The system can only show you which line is talking, so anyone talking in that room will show up as the room talking. There is no reliable way for the system to automatically identify individual speakers sharing a single phone line. See similar questions...

No. Using a speakerphone negatively affects the sound quality of the class for everyone. Everyone needs to call in on a separate line. Also, participants should register and pay for the teleclass individually -- this enables us to email them phone information and the link to the class page for each teleclass. This is a ministry -- we keep our registration fees moderate, and at this time they are our sole source of funding to cover the basic costs of holding our classes and paying our leaders. See similar questions...

Your regular device notification will occur (i.e., either your ringer, or your phone's vibrate function will activate as normal). Additionally, the display on your wireless device will indicate that you may either a) quiet the call notification or b) ignore the call and let it go to voice mail. See similar questions...

One of the great benefits of MarkeTouch Media is that all of our campaigns come enabled with Real-Time online reporting. From any web-enabled location, at any time of the day, you will be able to monitor the effectiveness of your campaign. See similar questions...

Go to that message (using Go to Message, previous or next) and then press 72 for envelope information. Envelope information will tell you who called and when they called. See similar questions...

Turn on extended ring indication, AT+CRC=1. This command is detailed in paragraph 6.11 of GSM07.07 and gives a more verbose output on incoming calls. See similar questions...