In most cases, your TV may only have one set of video inputs. If this is the case then you are limited to the amount of video product that you can connect to the TV. By connecting all your audio/video components directly to the receiver, you would only have to use one video cable from the receiver to the TV. This in turn simplifies the connections, which makes video switching easier.

To connect the audio output from the computer to the AV receiver, you need a stereo mini-plug to a stereo RCA pin cord. Then connect the line-out from the computer sound card to an available audio input on the receiver. Select the input and adjust the volume output from the receiver. See similar questions...

You typically have two options when connecting a powered sub woofer. Input (1) on the rear of the sub woofer would be used when connecting the sub woofer to the receiver using speaker wires. You would then connect the main speakers to the opposite end, or output or the sub woofer to the main speakers. Option (2) would be using RCA line level output jacks, input (2) on the rear panel of the sub woofer directly to the single sub woofer output on the back of an AV receiver. See similar questions...

To get audio from your TV through your AV receiver, please connect stereo audio cables from an available AV input on the rear of your receiversuch as D-TV/LD or CBL/Sat. Then refer to your TV owner's manual for more information about audio output to an amplifier. You may have to turn off the internal TV speakers in order to get any output from the TV into the AV receiver. See similar questions...

Yes, many Yamaha AV receivers are stable down to, but not below 4 ohms. We recommend that you use only speakers with a minimum of 4 ohms. Also, please make sure that the impedance selector switch is set to the correct position as recommended by the owner's manual. See similar questions...

If your current receiver has no subwoofer (RCA) line level output, you will need to connect the subwoofer to your receiver using speaker wire connections on the rear of the receiver. You first need to take the speaker input from the subwoofer to the A or B speaker terminals on the rear of the AV receiver. Then take the speaker outputs from the sub woofer and connect to the main speaker terminals inputs. See similar questions...

The short answer is don't try if you are new to home cinema as the back of one of these machines can be very scary. If you are determined to do it yourself then talk to your dealer first to make sure you have all the right cables for your system, then carefully consult the handbook to ensure you have everything in the right place. You will then need to balance the speakers and set up the sound levels. See similar questions...

No, the SRM 66 is a line level device. It will accept levels from consumer - 10 dBV or professional + 4 dBu sources but a preamp, like the MS 1b, is needed between the microphone and the SRM 66. See similar questions...

Probably. Any wireless receiver supporting the industry standard 802.11b or 802.11g protocols should work. However, in rare cases, we have found wireless receivers which had compatibility issues with the computer upon which it was installed. See similar questions...

A USB cable and the presence of USB connections are not yet adequate for exchanging data successfully. However, data transfer can be effected using a USB cable if a serial COM Port is emulated by the GPS receiver. The GPS data must be available in the NMEA 0183 format when data is called up online, so that Geogrid is in a position to evaluate these data. See similar questions...

All of Onkyo??s products are come with the both English and Chinese instruction manual. Every user can easy to setting up the system guide by the instruction manual. If the user facing any connection of operation problems. Who can be contact with our Customer Service Center through by either telephone or e-mail. For contact details, please refer to the Customer Support webpage. See similar questions...

Media Services will provide a projectionist to show your video, and help you reserve the equipment or room necessary, for any video showings during regularly scheduled class sessions. For special showings outside of class sessions, Media Services charges a nominal fee. For more information, contact Media Services at x64637. See similar questions...

Navtex receivers can be connected to NaviGator. Again they need to have the following pin connections: Pin 2 - NMEA / Position In, Pin 3 - NMEA / Position Out, Pin 5 - Ground. Once it is connected and messages are being received and they have a Lat and Long, they will be displayed on the chart for you to click on and view the message. See similar questions...

We provide an installation manual with step-by-step instructions. FSL equipment is designed for a wide range of interfaces and relays. For special applications, FSL can provide special interfaces. See similar questions...

The external input connections on the rear of the unit are designed for an MPEG2 processor that is very popular in Japan and was scheduled to come to the US. So at this point, there is no US made component that you can connect, short of a 6-channel separate processor that you can use for this port. At the present time, please ignore that section of your AV receiver. Currently, only the RX-Z9 and the RX-797 Stereo receiver are capable of accommodating a graphic equalizer. See similar questions...

You can connect a second display to a Kaleidescape Movie Player or Movie Player 2. The Player normally sends video to all video outputs but they cannot be controlled independently. The settings you make for the Primary Video Output in the Installer Web Utility apply to all video outputs. For example, if you set the Primary Video Output to match a 16?9 display and a secondary video output is connected to a 4?3 display, the image on the 4?3 display will be distorted accordingly. See similar questions...

Yes, you can connect the player directly to your computer using an Ethernet crossover cable. You can purchase a crossover cable at most retail computer stores. Once you have this connection, you'll need to set up your network adaptor and Squeezebox with static IP addresses so that they can find each other. See similar questions...

Sure. The onboard guitar preamp isn't usually necessary, but the AP 13 will work fine with most all varieties. Check to see if you need phantom power from the AP 13 though. This setting can be very important to maximizing performance with a second preamp. See similar questions...

All of Onkyo??s AV receiver are high current power design and its can be drive most of the speakers in the market. However the speaker system has its own specification with difference power requirement. Also difference brands speaker system has its own characteristics. So you are better to consult with the dealer and listen the sound performance you are searching for. See similar questions...

Connect one end of the Midi interface cable to Joystick port of your PC and the other end has to be connected to MIDI IN and MIDI OUT of Musical KBD. (Cable IN to KBD OUT to record midi and cable OUT to KBD IN to play back midi files) Note: If you have Creative Platinum Sound Card, you do not need Midi Interface cable as the sound card has its own MIDI IN and OUT port. You need only simple midi cable to make connection between KBD and PC.] See similar questions...