A building permit must be taken out prior to installation of a solid fuel stove (wood, coal, pellet, etc). A copy of the manufacturer's specifications should be included with the permit application. These general guidelines may be used to install most stoves, new or used. If the stove is new, installation is in accordance with the manufacturer's specifications and installation instructions. Many new stoves have built in features that allow you to reduce the minimum clearance guidelines below.

Almost every gas stove, gas insert and gas fireplace we sell is rated as a heater. They operate at efficiencies ranging from 30 to 70%. As a result, they often can heat an area as effectively as a woodstove or wood insert. Just like woodstoves, they come in many sizes and output ratings. It is important to size properly for your application.

Yes, a permit is required to install a wood or pellet burning stove. Currently, we charge $25.00 for fireplaces, wood or pellet stoves. (See 1997 UMC 112.1)

Factory built fireplaces or stoves capable of burning wood or wood pellets may be installed in manufactured homes provided they comply with the following State of Nevada requirements: quot;The fireplace or stove is approved or listed for use in a manufactured home or mobile home" quot;A fireplace or stove does not take the place of the normal heating unit or furnace of the manufactured home or mobile home.

No, we do not recommend doing this. If you changed from wood to gas, it would not only void the warranty of the gas log set, but you run the risk of damaging gas components in the log set itself and your home.

If you are using the wood flooring plans that we have provided, we recommend that you create a rock or sand hearth to put your stove on. To install your stove on the hearth, follow manufacturer’s instructions and local building codes. Each dome is equipped with a metal stove flashing. The piping will run from your stove through the flashing and above your dome. All of the piping that is used in association with the stove should be double walled pipe.

No. Since the pellets are so efficient, the stoves do not need a chimney. All you need to do is vent them outdoors with a 4” pipe through an outside wall. So, choose the room you congregate in, place the stove in that room, and enjoy the ease and warmth of pellet heat! You’ll also enjoy watching the flames—and the fact that there is very little ash to clean.

On average, one 40 lb. bag of wood pellets will heat a 1,500 sq. ft. home for one or two days—depending on whether the pellets are your primary or secondary heating source. The amount you use will also depend on other factors such as how much heat you prefer, the amount of insulation in your home, the outside temperature, and so on. Some people use pellets as their primary heating source while others use it as secondary heat.

Please make sure the flue is open before starting fire. NEVER remove hot ashes or partially burned loges. Please leave the ashes in the fireplace even if you are sure they are cold. It's easier to build a fire with a bed of ashes. If it becomes absolutely necessary to remove the cold ashes, use a metal container only. (Anything flammable, such as a paper bag or cardboard box, even if you are positive the ashes are cold, is extremely dangerous.

Unfortunately, no. You will need a wood pellet stove but if you don’t already have one, the savings you will realize in heating your home will more than pay for the stove. Some companies do offer converters which may be placed in fireplace inserts. Please check with your local hardware store or on the web to see if this option will work for you.

Yes you absolutely can from a technical standpoint. The building can have anything normal installed into it. Legally, we cannot answer that. You would need to check with your local fire department etc.Many places now require the Ultra low emission wood stoves and some areas no longer allow wood stoves. We cannot comment on that because we don't know your area, but yes a wood stove can be installed.

Gas-fired stoves are only made for the very largest of commercial saunas, where the high costs of installation and maintenance are bearable. For most applications, electric stoves are easiest to install with the lowest purchase price (especially at SaunaShop!), are virtually maintenance-free and are enjoyed with low running costs too - typical domestic and light commercial stoves use only 50-75 pence per hour in electricity.

Night and Day! Blaze King classic models feature a bimetal coil thermostat This simple thermostat evens out the uneven nature of burning wood. Blaze King owners typically only adjust their thermostats once or twice and day. Nearly all other wood stoves have a damper to regulate air-flow and require more frequent adjusting. Also, Blaze King wood stoves are very deep. Not just front to back but real depth.

You may leave the applicator on for more than 45 minutes if you wish to do so. During that 45 minutes most of the product has been absorbed into the skin so it is not necessary to leave it on longer. The product continues to work in your system for 72 hours so simply wear the applicator for 45 minutes, remove and rub in the additional lotion that was left on your skin. Wash off the next time you bathe or shower.

Most likely not. Average pellet stoves with a standard burn pot are not designed to cope with high ash content. In general, corn stoves will have more potential to handle grass pellets because they are designed to deal with a somewhat messy residue. This is no guarantee that corn stoves will burn grass, corn stoves sometimes have difficulty dealing with corn.

A final building inspection is required once the pellet stove has been installed per the manufacturer's instructions and per the U.L. Listing.

You need to determine which model of Blaze King you own first. Since there have been dozens of models made over the years, determining which model you own by general description is usually not possible. At the time all stove are manufactured, a metal or foil decal is applied to the rear of the stove. (Right hand side on inserts). This label contains all the information pertaining to the model and serial number.

A single wall black or close clearance double wall black to the point you would break surface of a wall or ceiling. Then you must continue with a 2100 degree chimney pipe to the point where you would be 2-foot above the peak or ten feet away from the roof line.

Do NOT attempt to relight the pilot light yourself. Please call the office at (812) 330-1411 and make a maintenance request.

Depending on the model you choose, you can install as close to 2" from the rear or sidewall. This means more space in your room, and less cost for installation. Be sure to check each stove's clearances before deciding.