QueryCAT Logo
Search 5,000,000+ questions and answers.

Frequently Asked Questions

How about NSN for WD1 or WD1A wire?

Frequently Asked Questions
WD-1/TT comes in a "donut roll" MX-306/G or MX-306A/G 1/2 mile wire. LIN: C68993 NSN:6145-00-160-7795 or NSN:6145-01-041-9989 $481.00 roll.

How about NSN's for other batteries?

Frequently Asked Questions
Here is a handy document listing frequently used batteries: Battery.doc To get a complete listing of rechargeables and other batteries check out CECOM's battery website at https://lrc7.monmouth.army.mil/QuickPlace/ipm/PageLibrary85256A2B0062C0F7.nsf/h_Toc/f8ded136ff17831985256b3e006cf4e0/?OpenDocument See similar questions...

What is the NSN for the AN/PRM-34?

Frequently Asked Questions
NSN 6625-01-094-5646. See TM 11-6625-3015-14. You can use CECOM's online database at http://lrc3.monmouth.army.mil/cecom/lrc/pie/pie_dbs/cfm/equip1.cfm to search for equipment data. See similar questions...

What are the characteristics of the wire?

Frequently Asked Questions (FAQ)
The wire is 39 inches (1 meter) long and per MIL-W-16878 (TFE insulation). One is red, plus (+) voltage and one is black (ground). See similar questions...

How do I wire a relay in my system?

Car Audio Installation FAQs - WikiFAQ - Answers to Frequentl...
There are two types of relays that are commonly used in 12-volt automotive applications: Single-pole Double Throw (SPDT) relays, which have 5 pins, and Single Pole, Single Throw (SPST) relays, which have 4 pins. Depending on the application, you can use either of these; for remote turn-on leads (see Section 5.11), an SPST relay is fine, SPDT relays are often used in alarm installations. Make sure that you get a 12-volt relay - this specifies the voltage required to make the relay "switch. See similar questions...

What is the NSN for the H-250 and the H-350?

Frequently Asked Questions
gets you 1 mile. 6145-01-259-9203 gets you 1000ft. Want the DR-8? Get it with: 8130-00-407-7859. For more on wire NSN's see PS Magazine article at http://www.logsa.army.mil/WEB-PAGE/2000/573/573-50-53.pdf See similar questions...

What is NSN for PLGR batteries?

Frequently Asked Questions
Battery, Non rechargeable (Hold-Up) BA-5372/U NSN: 6135-01-244-6441 Battery, Non-Rechargeable, BB-5590/U Manpack Primary Battery (Lithium Sulfur Dioxide $308.00) NSN: 6135-00-439-9450 Battery, Rechargeable, BB-390B/U, Manpack primary power ($254.00) NSN:5140-01-490-4317 TM 11-5820-890-10-8 See http://army-gps.robins.af.mil/PS_Mag/allabout.htm See similar questions...

What is a NATO Stock Number (NSN) ?

FAQ
When it is established that an Item of Supply is unique, its identity is fixed through the assignment of its own NATO Stock Number (NSN). NSNs are issued by National Codification Bureaus (NCBs). See similar questions...

What is a Wire?

Bank of Baroda
A wire at Remit2India Money Transfers allows you to transfer money from your existing bank account to India in 48 hours. Remit2India Money Transfers also gives you a unique tracking number for your transaction allowing you to track your remittance online at any point of time. See similar questions...

Why should my club apply for membership in the Night Sky Network (NSN)?

Night Sky Network: Frequently Asked Questions
Your club will join a national coalition of amateur astronomy clubs bringing astronomy and the excitement of NASA missions to your communities. Keep up-to-date on the latest NASA discoveries via members-only teleconferences with NASA scientists Your club can: See similar questions...

Where can I find the NSN for the SINCGARS battery box CY-8523C/PRC?

Frequently Asked Questions
I need the NSN for the sleeves/connectors (called bullets) for the TL-582/U wire splicing tool used to splice WD-1 wire. See similar questions...

How do I wire my Speakon connector?

Amplifier Frequently Asked Questions
CE Series amplifiers feature Neutrik Speakon connectors for output wiring. Speakons allow both channels of amplifier output to be wired to the same connector. See Crown's ProGuide for using the Speakon NL4FC assembly for complete instructions (pdf file, requires Adobe Acrobat to read). See similar questions...

What gauge speaker wire should I use in my system?

Amplifier Frequently Asked Questions
For the best speaker damping and least amount of power loss you will want to use the heaviest gauge that is practical. The length of the speaker wire should be considered when considering wire gauge. The shorter the run, the smaller gauge you can use with minimum power and damping factor loss. The longer the run, the heavier gauge you will need to minimize power and damping factor loss. You will also want to consider the size of power amplifier you are using. See similar questions...

Can I wire my investments?

Frequently Asked Questions
The Fund will generally invest in these themes in substantially equal 20% portions over time. However, asset allocation may varies based on availability and rebalancing criteria. Modern Portfolio Theory is based on Harry Markovitz's "Portfolio Selection," published by the Journal of Finance in 1952. See similar questions...

How do I wire my pickups up?

Frequently Asked Questions
Complete installation instructions and hardware are included with all of our pickups, accessories, and systems. In addition to basic assembly, there are often useful customization tips which are worth checking out. If you need a new copy of the installation sheet, contact EMGTek to get a new copy. We also have a set of our nine most common wiring diagrams available here online. This covers most basic setups, but you can contact us for assistance with any custom requirements you may have. See similar questions...

How do I attach wire leads to the piezoceramic?

Piezo Systems - Frequently Asked Questions
All of the PSI piezoceramic parts come with a thin (~3000 Angstrom units) metallic electrode already on the ceramic. Wire leads can be soldered (use ordinary 60/40 resin core solder) anywhere on the electrode to suit the application/experiment. Most PSI ceramics have thin nickel electrodes and require the use of an additional liquid flux for uniform results. Our Solder/Flux Kit was designed to make this task much easier. See similar questions...

How do I wire the output for unbalanced use?

Technical Support
Since this unit uses a cross-coupled output, it is imperative that pin 3 be grounded to pin 1 and the audio positive connected to pin 2. It is also very important to make sure the unit is earth grounded using a separate wire connected to the chassis ground screw near the red power connector. See Sound System Interconnection for further details. Not having an earth ground connection to the chassis is the number one cause of failure See similar questions...

Explore Other Topics

How do you determine the rental value/length of lease?
Do I need to take special precautions against malaria?
How long will the results of a Brazilian Wax last?
Can I install Quality Center in Windows Vista Home Basic Edition?
Can you substitute oil for margarine in all of the mixes?
How do I get rid of old gasoline/oil that I have in my garage?
How can I paint my baseboard without getting paint on the carpet?
What are the rates for the IDD / STD calls?
Where do fires occur?
How do I set the default MAPI Email Client?
How do I add new reports to the Shopping Reporting Engine?
How do you prepare morning glory seeds to best activate their psychedelic properties?
How do you overcome breathability in the rain in a hot climate?
More Questions >>

© Copyright 2007-2012 QueryCAT
About • Webmasters • Contact