With the current adapters you cant, the USB modem is the DSL equivalent of a WinModem and requires some processor power to perform the modem functions and convert the ATM data into TCP/IP for presentation to the PC. There is a Draytek device however which can effetively act as a router and presents ethernet to the user side. See details here.

It is an expansion card placed in a computer to support the ethernet network protocol across digital communications lines. See similar questions...

If you are purchasing a new PC, you should order it with an ethernet adapter pre-installed. If you already own a computer and it does not have an ethernet adapter pre-installed, we suggest purchasing a 3Com 10/100 Etherlink adapter. Laptop users can purchase a comparable PCMCIA card. Ethernet adapters are available for purchase through the IMU Bookstore or from local vendors. The ResNet system was designed for the use of a 3-meter patch cable (also referred to as a dropcord). See similar questions...

Absolutely nothing at the moment. All three are disabled. Some people have reported that USB keyboards work, but it's not a supported feature. Others have also powered a PC cooling fan off the USB, but that really isn't necessary. Just keep it well ventilated and it'll be fine. See similar questions...

Adapters with older Intellon chipset version (A1) run under Linux. You can find a driver for it in Linux kernels from version 2.4.19 higher.The new Intellon chipset versions (51X1 and 5200) are not supported under Linux for the moment. See similar questions...

You need to install your device drivers before plugging in your USB device. Insert the disk or CD that came packaged with your USB adapter and install the drivers from that disk. Then, after shutting down your computer, plug in your USB device and restart. Your computer should auto-detect the new hardware and offer to search for drivers. After it finds them, you will be able to use your USB device. When setting up your USB adapter, you will be asked for two settings. See similar questions...

The i.LON 10 Ethernet Adapter is designed to "keep up" with the channel for unacknowledged uplink messages. This means that the i.LON 10 Ethernet Adapter can pass up to 180 - 200 unacknowledged messages per second uplink from the FTT channel to the LNS or OpenLDV PC. Acknowledged service is slower. However, the performance is asymmetric. Downlink unacknowledged messages are limited to approximately 21 - 22 per second. See similar questions...

Yes if you specify this at time of ordering our installers will provide you with a suitable USB to Ethernet converter at time of installation See similar questions...

If you are connecting directly to one PC, under windows 98SE, 2000 or XP, either Parallel or USB is usually fine. However, the way XP handles USB devices may cause you to lose the device occasionally. This is because XP assigns virtual USB ports to multiple devices on the same USB bus. If the plotter is switched off or disconnected when the PC is booted up, it may be found later as a new device on a different virtual port, and the driver may need to be installed again. See similar questions...

Either one will work with the cable modem and service Wave provides. However, not all computer systems allow for a USB installation. Before your Internet installation, you must have a computer with a USB port, or have a 10 Base T Ethernet card installed in your computer. See similar questions...

You name it: telephones, modems, keyboards, mice, 4x and 6x CD ROM drives, joysticks, tape and floppy drives, scanners and printers. USB"s 12 megabit/s data rate also accommodates a whole new generation of peripherals, including MPEG-2 video-based products, data gloves and digitizers. See similar questions...

The Andrea USB adapter is a half duplex device which means that it does not allow you to listen and talk at the same time. Part of the reason the Adapter works so well with our mask is that it does not have additional computer to audio signals to corrupt the input signal from the Sylencer. Instead, it provides a jack and adapter cord (with pink ends) that will plug into the USB wire side of the adapter that plugs into your computer sound card. See similar questions...

You need to install your device drivers before plugging in your USB device. Insert the disk or CD that came packaged with your USB adapter and install the drivers from that disk. Then, after shutting down your computer, plug in your USB device and restart. Your computer should auto-detect the new hardware and offer to search for drivers. After it finds them, you will be able to use your USB device. When setting up your USB adapter, you will be asked for two settings. See similar questions...

Plug the wide flat end of the USB cable into the downstream connector located on the back of the computer or USB hub. Plug the square end of the USB cable into back of the USB box. Once the cable is connected to the USB box, the "Add New Hardware Wizard" dialog window should appear. Select the recommended option: 'Search for the best driver for your device' and then press the 'Next' button to proceed to the next window. See similar questions...

Please check if the Service Pack 4 is ready in the system. We found this is the bug of SP4 (please see 822831 - BUG: Driver Installation Program Does Not Install Device Drivers http://support.microsoft.com/default.aspx?scid=kb;en-us;822831) You can download the hotfix at http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=7c896e82-4b50-44c8-a634-3227c0e71293 to solve the problem. See similar questions...

Since the release of Windows XP and laptop manufactures often only installing USB ports, users are finding that a USB to serial adapter is the only way they have to communicate with their CNC machines. Unfortunately many manufacturers of USB to serial adapters are not 100% compatible and communication to their CNC machine is either unreliable, very slow, or limited to one way transfer. See similar questions...

Very doubtfully. The total link speed is still bound by the slowest link in the chain. That link is almost certainly the physical interface on your Magellan and not the serial port on your computer. Even if you have a super-spiffy USB 2.0 serial adapter that's talking at 480Mbits/second to the host, the speed is still limited by the max speed of the serial interface (a max of 115.2Kbits/sec) when talking to your unit. See similar questions...

Q6:When trying to install the USB driver in Windows 98, there is an error message saying that some file is missing Q7:When trying to install the USB adapter in a WinXP machine, the PC reboots automatically after the installation with no error messages. Once the PC is rebooted, an error message appears: ??Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39)?? See similar questions...