Answer. An Indent is a Document that defines a need for a material or service. It is a request to the Purchase Department for buying a specified quantity of the required material within a specified time period.

This is a custom factory order which means we produce and decorate the item in an overseas factory. There are minimum quantities required to make this option feasible, lead-time is between 12-14 weeks for sea freighted items or 8-10 weeks air freighted. To search by category and colour for example if you were searching for a particular colour in novelty items. See similar questions...

Answer. The indents can either be directly used to raise the Purchase Order Or can go through the Proper sequence of Requesting of RFQ from different Vendors then Rating the Quotations received from different Vendors and then raising the Purchase Orders. All the indents can be directly used to raise the Purchase Order except the Indents whose status is 'Closed'. Many Requisitions can be clubbed together to raise an indent. See similar questions...

Answer. An Indent can be raised with reference to the item requisitions from the Inventory but reference of the requisition(s) is optional and depends upon how the Indent Type is defined in the system. However, it is always relevant to create an indent in reference to an item requisition, for the purpose of MRP. See similar questions...

Answer. If user doesn't or can't raise an indent, it is for the MRP or the purchase manager to fulfill the demand. To fulfill the demand, both MRP as well as purchase manager will create indents. In both cases, indent will not have info about item requisitions. MRP will estimate the requirement by looking at the current stock, safety stock and requisitions in hand. It will raise 1 or many indents for the balance requirements. See similar questions...

Using jEdit's default configuration, you can indent a selection of text by pressing ALT+RIGHT. Unindent a selection by pressing ALT+LEFT. See similar questions...

There may be times when editing a document, that you need to indent an entire paragraph. Word offers a shortcut for this format: Normally the tab stop defaults at .5 inch intervals. Use the ruler located at the top of your screen to view the tab stops. You may also adjust the tab stop to a new default. To do this: Word will then move the left and first line indent marker to the left one tab stop at a time until it reaches the 0 position on the ruler. See similar questions...

This is difficult to do, unless you know how to use LaTeX software. See "Using LaTeX commands" section above. See similar questions...

Answer. When the Indent ordered qty for all items is included in the Purchase Order then the Indent can be considered as 'Closed'. See similar questions...

That depends on what you mean. If you want something that works like vgrind on Perl programs, then the answer is ''yes, nearly''. See similar questions...

The shallow channel is to provide the alignment for the two motors as they are being epoxied to the wood block. It increases the epoxy contact surface to the motors (and thus the strength of the bond), and allows the use of a strong rubber band across both motors to hold the motors in position as the epoxy cures. In this way the motor axles are pointing in the exact direction they need to be for alignment with the end holes of the white plastic L-pieces (Custom lever arm and pivot, item #3). See similar questions...

DrJava has a very useful indenting algorithm, but indenting several large files can be time consuming. Because of this, we provide a command line interface to the indenter that you can run on a series of files. From a command line, use the following command to run the indenter: Where VERSION is the correct version number for your copy of DrJava and FILES is a list of the files you wish to re-indent. See similar questions...

Answer. System treats indent as demand fulfillment/ supply of materials. By linking with a requisition, system can establish a relationship between demand & supply. See similar questions...

The performance of T&B Sta-Kon terminals is not hindered when crimpedin any radial position on the wire barrel. The crimp indenture can be located on the seam of our brazed terminals, on the backside of the barrel of all terminals, or on the topside of the barrel of all terminals. See similar questions...

Under the Defaults tab of Preferences, you can set the default First Line Indent amount for new documents. To adjust this setting for a specific document, select the text to change, open the Inspector (Format > Inspector...), then increase Indent - First Line to the desired amount. See similar questions...

Question: School did not do so well last year with the presentation portion of the challenge. We wanted to see if there was a rubric that is used for this area. Also, we wanted to see what the general format of the presentation is – should they be talking about their construction and testing process? Or, should they just be prepared to answer questions? We want to make sure that the students do better in this area. See similar questions...

Fire restrictions or bans on the Daniel Boone National Forest may be issued by the Forest Supervisor if a high risk for wildfire is determined. The Kentucky Division of Forestry can issue fire bans by county, which may include the Daniel Boone National Forest. Conditions that may warrant the issuance of fire restrictions include high temperatures, low humidity, dry woodland ground fuels, and an increase in the number of wildfires. See similar questions...

Well apparently it has to do with something called gene expression, which refers to the pattern in which genes are switched on and off. And gene expression has a major effect on your body's biological processes. Each cell in your body contains a 'power-factory' that produces energy, called the mitochondria. See similar questions...