Soy?Gel™ will remove multiple layers easily! Just allow the product to work until all the coatings have softened.

Soy?Gel™ has proven to remove most coatings including lead-based paints, enamels, oil and water based latex, varnishes and urethanes.

Soy?Gel™ will not raise the grain of the wood. (Rinsing the product off with too much water may cause the grain to raise, though.)

Soy?Gel™ has an extremely low evaporation rate. The product crystalizes when being left on for extended periods of time or in a mild - heavy breeze. Just add a little water and the product turns back into a gel. When using BEAN?e?Strip™ in outdoor applications, the surface to be stripped may be covered with plastic to help keep it from crystalizing.

The Best Aromatherapy Gel Candle™ Collections are made of clear, sparkling gels infused with fragrant oils or aromatic essential oils. When lit, the light reflecting from the clear gel creates an alluring and claming environment. Tiny luminous bubbles in the gel produce a sparkling effect. The Best Aromatherapy Gel Candles™ are long lasting and burn much cleaner with less smoke. As each candle burns the gel evaporates permitting longer usage.

The recommended application methods are to either an airless sprayer or a paint brush. When using a paint brush, make sure to use a "glopping" method when applying. Get the product on THICK. (aprox. 1/8")

Remember "Thicker better, longer stronger". Generally Soy?Gel™ can take anywhere from 5 minutes to 8 hours depending on what is being removed and how many coatings are to be removed. Let the product do the work. Test the surface every 20-30 minutes until the coatings begin to soften and are ready to be removed.

Yes, Soy?Gel™ works great on teak. Do not let the product sit for an extended period of time on the teak as it will start to extract the oils of the wood. If Bean?e?Strip™ is applied to raw teak, it will extract the oils and raise the grain.

Soy?Gel™ is 100% biodegradable. Check with your local landfill or EPA office about disposal of the coatings you are stripping.

You may mix any of our urethane clears into the final coat of an ULTRA-GLO acrylic urethane paint job. Doing so is a quick and easy way to improve the gloss and long-term durability of the paint finish, without having to apply a full clearcoat. It should be noted that this is not as effective as applying a full clear coat. Kirker’s ULTRA-GLO acrylic urethane paint is completely compatible with all of our urethane clear products, so they will work together in any mix ratio.

Yes it will, however you may find you need to prepare the surface using a solution of 80% boiled linseed oil and 20% mineral turpentine. This solution can be applied either with a paintbrush or a spray bottle. Once the solution has soaked into the paint and the wood for at least 24hrs use the Speedheater method again to remove the paint.

If your car's paint is in good condition to begin with, the adhesive will not cause damage. Plate may be removed with the aid of a hair dryer to soften adhesive. Soften a section at a time and gently pry up as each section becomes soft. If carefully removed your Promo Plates plate may be used again by applying a new adhesive backing.

Yes. Allow seven to ten days drying time for surface to be completely dry and cured. Both water- and oil-based products can be used.

A - Not at all - even compared to mainstream paints, they remain very competitive indeed, but many brands are sold only in non-standard sizes, such as 2L or 2.25L, which makes direct price comparisons difficult, but if we compare like for like for 5L, for example, below is a cross-section of Matt coloured wallpaints seen at one of the leading DIY stores in Feb. 07

The best analogy is to the way cartoons used to be animated. Each component of a scene would be painted on a transparent film, and then each film would be stacked or layered over the other to produce the complete composition. In this way, you could easily animate a person walking because his legs could be animated independantly of his body, for example. Similarly, complex images can be broken down to layers within GIMP and each layer can be processed independentlly of every other.

Yes, Automotive paints of the past were lacquer and enamels that, with care can be repaired and maintained as easily as the epoxy and urethane paints if applied correctly. I also heard about Sico Acrythane industrial paint. Then there are the PPG systems and of course, the usual aircraft paint. I have even heard of people using marine paint with a roller. Later in this website a section will be posted on how to paint your plane. ~ cdngoose

Polyurethane is a term used to describe a wide ranging family of elastomers (any compound exhibiting the characteristics of natural rubber; stretchy and elastic.). Poly meaning "many" and "urethane" the classification of the chemical structure. Polyurethane or urethane for short, is used as a solid cast material (bushings). Polyurethane can be as soft as a rubber band or as hard as plastic.

Numerous raster layers can be loaded into the viewer workspace and then quickly displayed with a single mouse click.

The development team did not include multiple piping layers for several reasons. If a user wants a multi-layer flushing system they can take the cost for piping 1 layer (the cost AMDTreat produces) and multiply it by the number of layers desired. This cost can be placed in the "Other Costs" module as a capital cost. In primary pond, why is the pond L:W assumption 2:1? Why can't the user change it? Site conditions often dictate long narrow ponds and this would be helpful.

Phase 1 will loosen the paint, but it is the mechanic who will use different chemicals to remove the paint. It will not remove paint on a gym floor. It has removed oversprayed paint.