While Kirker markets our PERFECT PRIME and RAPID PRIME 2K urethane primers as “tintable,” it should be noted that our suggestions will yield only a tinted shade, and not a complete shade of the color you are using. Both of these products are available in gray and buff (cream). To tint either color, we recommend using no more than 4 oz. of ULTRA-GLO acrylic urethane paint per each sprayable gallon of primer (or 1 oz. per each quart).

The SDRAM has multiple internal banks. The 16M SDRAM has 2 banks, the 64M has 4 banks. When you tell the SDRAM a ROW or COLUMN address you must also specify which BANK you are referring to. The way to do this is by the 'bank address' (BA). Herein lies the problem. For some unknown reasons, suppliers have lumped together the ROW address pins with the BANK address pins and simply refer to them as 'address' pins.

Primers-sealers provide a variety of performance properties such as stain blocking, corrosion inhibition, surface filling, and enhanced hide. Their main function is to satisfy the porosity of the surface so the topcoat does not penetrate into the substrate. The result is a surface, when topcoated, that looks better and lasts longer.

We have tested tinting over the Clear View kit. The Clear View heating elements are slightly higher off the glass than factory defrosters so the tint may not form a good tight seal along the sides of the heating element. We have had satisfactory results but not perfect. Another challenge is the kits bus bars are 1/4 inch above the glass when installed but the tint can be trimmed to fit these we have found in some vehicles without making it look odd.

Yes, flat glass skylights are very popular to tint. The heat build-up that comes through skylights is a tremendous overload for AC units. It is recommended to apply a stronger shade of tint on skylights.

Heat tint is a mottled rainbow -like discoloration on stainless steel that is caused by excessive heat. Heat tint can usually be removed with a commercial stainless steel cleaner or steel brush commonly found in supermarkets.

Dilute a few drops of food color with 1 teaspoon water in a large resealable plastic food storage bag. Add about 1 cup of flaked coconut. Close the bag and shake well until the coconut is evenly coated with color.

All tint fades with time. If you would like a long lasting film try our Quantum polarised film which has a manufacturer's lifetime warranty. Now you can also try our Supreme Series, which is non-reflective and also has a manufacturer's lifetiime warranty.

Tinting film is usually a very thin layer of clear polyester film with tinting agents such as dyes and/or metals infused onto the film. Once this tinting film is applied to a window, how outside visible light comes through that window becomes altered. Normal auto glass without any tint applied will Reflect around 5% of visible light (known as VLR%), Absorb another 5% (known as VLA%), and Transmits 90% of visible light (known as VLT%) into the car.

The 2k x 2k CCD camera has an area more than 6 times that of the 1k x 1k MultiScan camera. The pixel size is 25% larger for the 2k x 2k camera, which results in better image resolution.

For holography applications, a 2k x 2k CCD camera is preferred. This is because the reconstruction of an electron hologram only uses roughly 1/4 of the image area. For a 1k x 1k camera, this means only 256 x 256 pixels. For 2k x 2k camera, the reconstruction can be as large as 512 x 512 pixels.

You need to add 10% of Infralsi to the total volume of your primer. This is after you have added all your other products to the primer. Infralsi is the last item that must be added.

The owner of Northeast Tint, Charlie G. Arakelian, has 15 years of tinting experience and is ranked 2nd best window tinter in the world 2005 by the International Window Film Association (www.iwfa.com). Six judges put Charlie’s skills to the test through an intense competition of cutting, splicing, seaming and cleanliness, and chose the best of the best (read more) selecting him over other world competitors.

Prices range depending on the type of vehicle and tint preferences. All installations include a nationwide, lifetime warranty.

When will I get my sequence if I submit samples in individual tubes? The turnaround time for individual tubes is 1-3 days depending on if the sample needs to be repeated. Most sequences are returned within 1-2 days from when we receive the sample.

Once a project is completed the templates are discarded and primers are returned to you. If you need the primers for another project they must be resuspended at 4µM in microfuge tubes and resubmitted.

For Yale researchers -the remaining primers are dried down and placed in an envelope, together with the oligo specification sheet, and placed in the data return boxes in BCMM 305 to await your pick-up. For outside investigators -the dried primers are mailed out at the end of the project.

This varies depending on the primer used. Some have an "on part life" of up to a month, whilst others have shorter lives, perhaps even only a few hours. Contact our offices for further details..

No, our trained professionals clean the interior surface of your glass with soap and water using razors and squeegees prior to applying the film to make sure the surface is as clean as possible.