Yes. Aside from the fact that all of our fireplaces radiate heat from their fronts, there is still heat that can be withdrawn from the fireplace. Using the blower increases the airflow thereby maximizing the heat being conducted from the back side of the fireplace. Adding a fan is easily done if 110 power is hooked up to the electrical box inside the unit. If power is not already at the fireplace, it still may be possible but may be more costly.

Yes, aside from the fact that all fireplaces radiate heat from their fronts, there is still heat that can be withdrawn from the parts of the fireplace body that are closed in behind the wall. While there is an air channel that allows air flow around the firebox, allowing it to absorb the heat via conduction, this channel is somewhat restrictive by its size.

Blowers are optional on most heat circulating (grilles on top and bottom of fireplace) units, and some hearth products the blower is standard. Adding a blower is easily accomplished if power (110 VAC) was provided to the electrical junction box of the fireplace at the time of initial installation. If power was not provided, a fan option is still possible, but installation is complicated and therefore more costly.

PilotGEEK will continue to evolve and offer publicly available services to registered cell phone users for $14.99 per year. There may be a time in the future where a premium service will be offered at a higher cost for services not available elsewhere, but at this time there is none in the works. The free briefer uses cookies to remember where you were last. If you have cookies disabled, the browser won’t be able to save your information.

A32 - The sound output of any speaker has reached its limit, when the distortion becomes objectionable. It may sound too loud and intolerable, even when the sound pressure level is not exceedingly high, because we unconsciously judge loudness by distortion. A clean speaker can play at very high SPL and you may not be aware of it, until you try to talk to someone and find yourself shouting.

The ETS Cell within NightStar can power more than one LED, and with each LED added, the light output will increase. However, power consumption will also increase with each LED added to the system. Consequently, the duration of light output obtained from a fully charged capacitor will diminish, thereby requiring NightStar to be shaken more frequently. Adding more LEDs will also increase the cost of the device.

Many of our gas fireplace models that have louvers or grills on the front can have a fan kit added. You will want to make sure that electricity is run to the junction box underneath the fireplace first, before ordering & installing a fan kit. You can test the junction box by plugging a lamp into the junction box and switching it on and off. Also make sure the circuit breaker is not tripped.

AXTRO® is capable of heating areas above 260 square meters (buildings constructed to regulation 10/91) with any number or type of radiator installed.

Solution: Gradually close the air control mechanism in order to keep the flue temperature within the comfort zone, between 250 and 475oF (150 to 250oC). If you do not have a chimney thermometer and would like to get one, visit your local Osburn dealer. Solution: Replace the gasket using a genuine OSBURN adhesive and gasket kit. Please consult our accessories sections. Solution: Put less wood into the fireplace. The fireplace will not produce as much heat and will not heat as long.

Solution: Use smaller pieces of wood and place them to allow proper air circulation between the logs. The same weight of wood cut in many small pieces will produce more heat than fewer, larger logs. Only add big logs when you have a good bed of red embers. Logs with a diameter exceeding 6 inches (153 mm) should always be split. Avoid stacking logs to the top of the fireplace. Solution #1: In many cases, a weak draft is simply due to insufficient heat in the exhaust system.

InFlame Fireplaces have a heat output of up to 9000BTUs/hr depending on the fireplace. This is guaranteed to bring ample warmth to any room in your home. A typical electric fireplace offers from 1500 to 5000 BTUs/hr (approximately.) so our entry level 6000 BTU/hr max. output fireplace will provide you with a great heat supplement.

Several capacitors were studied during the development of NightStar. NightStar currently uses a 1-Farad, 5.5V capacitor. A capacitor with an energy storage capability 3 times greater than this is also available (3.3-Farad, 5.5V). However, it would require 3 times longer to fully charge this capacitor. The 3.3. farad capacitor is also larger and would increase the size of the flashlight.

Your shopping session will stay active for 20 minutes after the last page request. If you add items to your shopping cart and leave the session inactive for 20 minutes or quit the browser before completing the checkout process, you will lose the shopping cart contents and will have to start again. This is common behaviour with on-line shopping carts as it frees up web server resources for other customers.

There are a few precautions to take before implementing this TV application. First, take a thermometer and tape it to the wall above the mantel (where the plasma TV will be placed). Then and build a fire, let it roar while. Check the thermometer. If the temperature is above 90 degrees then the area is receiving too much heat - either escaping from the front of the fireplace and rising up the face, or radiating through the chimney to warm the outside wall.

Most amplifiers used for Wireless ISP purposes (including 2.4Ghz flavors) are rated for output power. Therefore, input power and losses prior to the amplifier can be ignored. Typically, the amplifier is mounted very close to the external amplifier, without any extension cables or extra connectors.

The sound of the microphone is controlled by your television system. The audio mixer simply interrupts the usual signal between your television and DVD player to allow you to add in microphone ports and has only limited volume control. In addition to the TV volume controls, you can also link your system through your stereo to improve the quality of the output.

Yes. This can be done through the use of a more powerful transmitter or with a power amplifier. However, both of these options will place the power of the unit outside of the limit allowed under FCC part 15 requirements. The FCC requires a license for systems at higher power levels.

Options can be added in any order. Options that must be combined are usually supplied combined. For example, the subreceiver option includes the subreceiver itself, as well as a second DSP board. These two items are only available as a single option. Each module purchased for customer installation will come with instructions. No special equipment will be needed.

Certainly. You may increase your investment whenever you wish. After sending additional funds (minimum US$10,000 or the equivalent) to the insurance company, they will automatically issue you a supplementary annuity certificate. Technically, this means you purchase a new certificate in the currency of your existing certificate or, if you so choose, in another currency. To simplify this procedure, you will receive a Policy Kit.