In northern Europe ideally, between 30 and 50 degrees; however, the system will work quite effectively from flat to vertical. For any other parts of the world please contact us for advice. We would always encourage you to check with the appropriate local regulatory bodies before purchasing a system. Local Authorities are charged with the responsibility of trying to reduce energy consumption in homes and are normally very receptive to innovative energy saving products such as SUNWARM.

X-5 X-treme, V-600, V-600CS, V-400E, V-300, V-300CS, V-300-7 and All Fold-A-Vent Products can be used with any roof pitch from 3/12 to 16/12. For hip applications minimum over all roof pitch must be at least a 4/12 pitch. (The old style V-400 can only be used with up to a 10/12 pitch roof.) See similar questions...

The roof pitch refers to the angle or the steepness of your roof. Builders can use a carpenter's square to find the angle of a roof. See similar questions...

Yes. We offer a 35mm modular low pitch conservatory roof system, which comes as an installation ready kit. Known as 'L2 in a Pack', this system offers sculptured cappings as well as the option of opal, bronze or 'Silhouette' polycarbonate. See similar questions...

If you do not see a question you may have listed here, please email Support at support@hartshearth.com or call us at 800-924-0850 and ask us. We are more than happy to answer all questions. See similar questions...

Garages - 10 or 12 degree roof pitch or we can accommodate a 22.5-degree roof pitch to match the roofline of the majority of older style Australian homes. Raised Barns - 10-degree roof fall on the sides and a 20-degree roof pitch in the centre raised section. See similar questions...

Grace recommends that the Grace Ice & Water Shield is extended a min. of 24"" beyond the inside face of the exterior wall line of a building and should extend from the eave above the highest expected ice damn. Check local codes and regulations as they may vary. If installing full coverage of Grace Ice & Water Shield, use same roof area calculation for finished roof covering. See similar questions...

We have design and reengineering resources to produce very complicated roof designs that can include high roof slopes as well as various roof configurations within the same project. See similar questions...

The roof pitch is the slope of your roof. You can determine yours with a level and tape measure. Click Here for more info See similar questions...

Amazingly, quite low: as little as 1/2:12 (1/2" to the foot) for standing seam metal roofs - a definite benefit for many low-pitch applications. Most other roofing systems require minimum pitches of 3:12. See similar questions...

A 4:12 pitch is standard on all Uni-Frame® and Town & Country buildings. Any pitch can be accomodated, however. See similar questions...

Moisture is the primary cause of a roof’s deterioration. The steeper the slope, the quicker rainwater and moisture will run off. See similar questions...

If a card has "Pitch" in the text box, then you can send it to the discard to use the effect that's after the "Pitch" word, but you have to start defending in the next zone. Also, if you Pitch in your red zone, your opponent gets a point because if you Pitch in the red zone, it's like Focusing in the red zone. See similar questions...

It depends on the type and size of the greenroof. Most homeowners could check a flat or low pitch greenroof. A roofing professional should if it is too large or intensive – you can include a maintenance agreement of at least twice per year with the greenroof contractor/greenroof company. Or you can work out an arrangement with the roof maintenance staff of your building. See similar questions...

Yes, although we do not recommend the application of our product by a novice do-it-yourselfer. By following our detailed installation instructions, an experienced do-it-yourselfer can install Springhouse Shingles with relative ease. See similar questions...

When softwoods are dried, pitch sets at whatever the final temperature of the drying cycle. For example: if the last step in drying was 120° F. (49° C.) then the pitch won't run unless the wood is heated above 120°. The furniture industry usually expects pitch to be set at 160° F. (72° C.). See similar questions...

I use the pitch gauge made by Miniature Aircraft. There are many different brands out there, whichever one you use place it on the last 1/3 of the main blade. This is the part of the blade that counts the most. The last 1/3 is where almost all of the lifting force comes from. Level the flybar, sight down the pitch gauge and rotate it until the top edge of the gauge is parallel with the flybar. See similar questions...