The shotcrete is field applied either by hand or machine application on both sides of the panel. This part of the operation is very specialized. We recommend a reputable Stucco Contractor or a combination of both Contractors for this part of the operation depending upon the desired finish. For architects with a special finish in mind we would like to mention that the architectural molds or metal trim could be incorporated into your design to achieve the desired finish.

A standard Genset is usually supplied with a manual control panel. In this case, the engine is started from it own control panel and after the rated speed and voltage have been attained the switch in the manual panel is put on to connect the Genset to the load.

Shotcrete was originally called "Gunite" when Carl Akeley designed a doubled chambered cement gun in 1910. His apparatus pneumatically applied a sand and cement mixture at a high velocity to the intended surface. Other trademarks were soon developed known as Guncrete, Pneucrete, Blastcrete, Blocrete, Jetcrete, etc., all referring to pneumatically applied concrete.

A. Monolithic installation requires that each tile be laid in the same direction to create the appearance of a uniform, whole floorcovering.

The hair is individually bonded using the latest Ultra Sonic technology. Holly is one of the few in the Mid Atlantic to provide this advanced application technique.

We can apply exterior gypsum sheathing, plywood, OSB, Dens-Glass, rigid insulation, Exterior Insulation Finish Systems (E.I.F.S.), Thin Brick Systems, Hardy Plank, or other requested finishes.

Panels are .062" aluminum that is sanded vertically to give it a nice finish, then the edges are masked and the panel is painted with a coat of 'Polane' industrial paint. A very light splatter coat is put on top of that, then the panels are silkscreen printed. See this up-close picture of a panel. Moog modular panels used a different process that is somewhat dangerous. See this email from Bob Moog concerning Moog Modular Panels.

Rapid Set® cement is a high quality cement that is manufactured in a tightly controlled process. CTS is not in control of the manufacturing process for other cements and therefore doesn't know the quality or contents of those cements. Blending Rapid Set® with other cements is not recommended.

Panels are designed, cut and assembled to very specific tolerances at the Universal Foam Tech, Inc. plant. Each wall and roof section is custom made for a specific home. Therefore, both builders and home owners have confidence that the Universal Foam Tech, Inc. system is made specifically for their use.

No. However, if you don't want Wine as a dependency, you can bundle your private version of Wine into your package (.rpm/.deb). Wine has good support for such a setup via the WINEPREFIX environment variable.

A variety of cements (zinc phosphate, glass ionomer, resin modified glass ionomer and resin cements) are used today. Fiber posts require adhesive resin cements. Conventional cements should only be used for metal posts with retentive surfaces, if at all. We recommend RelyX??? Unicem??? cement along with the RelyX??? Unicem??? Aplicap Elongation Tip for direct dispensing of the cement into the root canal.

Install over existing plaster or drywall onto studs - wood, or metal. The dry wall backing does provide some added strength to the panels – installing directly onto studs should be for applications that do not require maximum load carrying capacities). Panel adhesive is recommended for more permanent installations. Drywall screws of the proper length work the best. Drive the screws through the backs of the groove (be careful not to damage the groove lips).

Solexx greenhouses are made with polyethylene. Polyethylene is much more flexible and is easy to cut to any size. Polycarbonate panels tend to be thicker, but have about the same insulation factor as polyethylene. Both materials diffuse light, but polycarbonate diffuses less (because it is more transparent), making the greenhouses much hotter in the summer. Polyethylene is very easy to clean and will not scratch like polycarbonate.

Solexx panels can be cut with a simple utility knife. Because the material is so flexible, it’s also possible to bend it around many curves and corners on a structure.

Diodes, Inc. manufactures its dual transistor products using separate die which are wire bonded to the lead frames. They are not monolithic devices.

Answer: Monolithic slabs are foundation systems constructed as one single concrete pour consisting of typically a 4 inch thick concrete slab with interior thickened portions under load bearing walls and thickened at all perimeter edges.