Yes, you can get suction in a Dentalaire station. Most veterinarians work on a wet table, which eliminates the need for suction. Using suction requires an assistant and significantly adds to the clean up time.

horsepower per dental station, which will run the high speed handpieces and low speed handpieces for hours of non-stop dental procedures.

If you desire suction or want to use a sonic scaling handpiece as your main method of scaling, you should consider a one horsepower silent air compressor. Suction and sonic scalers place a much larger load on a dental compressor.

All three Femco designs can drain by gravity or suction. Simply connect your suction system to one of our drainers and non-return valves.

Dentalaire compressors are extremely quiet, odorless and are legendary for their workhorse construction.

They come with a one year warranty. The only exception is the piezo ultrasonic scaler, which comes with a two year warranty.

Otherwise called Liposurgery, it is sucking out and cutting out excess, ugly & irregularly distributed fat mass with or without excess skin too. "Liposuction" is removing exces fat under the skin using metal tubes (cannulae) and powerful suction through tiny punctures leaving hardly any scar. When liposuction is combined with excising excess of skin also it is called "Lipectomy". Younger people generally do well with Liuposuction since skin is very elastic.

a metering pump manufacturer we like to see suction lines no longer than 10? and a pipe size larger than the suction connection of the metering pump.

In systems with longer suction lines, a pulsation dampener can be installed on the suction header, adjacent to the metering pump connection. The dampener will benefit the metering pump by acting as a day tank.

Suction relief valves are mounted as close to the suction mouth of the suction line as is practical. It can be opened manually to allow extra water into the slurry, or automatically if the suction or discharge lines begin to plug, as measured by vacuum and pressure sensors. The suction relief can also be connected to a Production Meter System to help keep at a consistent level of production.

The lumen of the blocker is patent and can be used to apply suction to assist deflation of the indicated lung or segment as well as the application of CPAP.

Yes! A properly installed Beam system offers the same powerful cleaning performance at every inlet whatever the distance from the power unit.

The first thing you should check is if all the other inlets in the house are completely closed. Then see if there are any holes in your hose. Lastly, check to make sure the system is cleaned out properly. With a single unit vacuum system (one piece), first drop the canister and empty it. Then, without putting the canister back in place, wrap a garbage bag around the base and push into the bottom of the vacuum (through the bag) a toilet bowl brush.

Probably not. First you should check to make sure that there are no other hoses plugged in or inlet valves open in your home. Then you should make sure that your canister is empty and your lint screen is not clogged. Next you need to determine if there is no suction at all your inlets. If you go to any inlet valve and open it up, you'll notice two small brass "beads" on the inside edge.

Loss of suction is an indication of a possible clog. When this happens, turn your vacuum off immediately as running a clogged vacuum could possibly overheat and then damage your motor. You may need to change your paper bag or

Holding this button down while your Pore Cleanser is operating will increase the suction pressure for a stronger cleaning. If you have sensitive skin, you should use this feature carefully. The mist cools your skin and closes your pores after you finish treating your skin with the Pore Cleanser. Fill the water tank with water. Turn the suction switch on. Hold the Pore Cleanser about 2 inches away from your face, and press the mist button to spray mist onto your skin.

The MICRODOLLY SUCTION MOUNT Camera Plate can be attached to any round or square surface tube up to two inches thick, such as a bicycle or motorcycle by using our modified Cardellini MOUNTING CLAMPS. Any combination of the suction cups and clamps can be used.

Yes, we can. For example, we can add suction, a one horsepower motor, fiberoptics in the highspeed handpiece, ultrasonic scaling units, or almost anything else you desire. Since we are the manufacturer, we are happy to customize your unit to your desired individual specifications.

A. Always lubricate high speed handpieces and low speed handpieces before every use. This takes only a few seconds. D. Make sure oil level is visible in the glass eye (at least half way up) on the back side of the compressor. Please note: Oil level is too high when you do not see any air bubble. If this happens, do not run compressor and call Dentalaire.

Yes in most cases. Any standard "four-hole" handpiece will work with your Dentalaire station.