No tools are required to assemble the raised beds. However, to set the pins flush with the top of the planter, a hammer (or nearby rock) may be needed in order to pound the pins into very hard ground. More often, though, the pins can be pushed flush by hand, or left exposed a few inches for use with a shade cloth or greenhouse covering (see below).

Assembling a Solexx Greenhouse is takes just a few readily available tools. You will need a screwdriver, variable speed drill, sharp knife or utility knife, tape measure, step ladder, GE Silicon-2 caulk, caulking gun, clear PVC glue and a level. I am interested in your Solexx polycarbonate covering. How do you install it? Our specially formulated Solexx greenhouse panels are actually a polyethylene blend.

We provide a hardware pack in all of our units that include all the necessary tools to assemble the product.

You'll need a 3/8" wrench (preferably socket wrench) to assemble the bed. In addition, it is best to have an extra person available to assist.

You will need a size 2 cross head screwdriver for assembly. A mallet may also be useful to help push bungs home. Any allen keys, nuts and bolts required are supplied with your product. back to top

Assembly is only required for our beds. All our beds are supplied disassembled to minimize shipping costs. Each bed will come with written assembly instructions and a list of the tools (usually just a hammer and a 3/8 inch socket spanner for the Round Hill bed) required for assembly. Each part is numbered. Bamboo dowels are included to pin the joints together.

All Bell'O? products include complete assembly instructions, and include all fasteners and tools needed. Average do-it-yourself skill is all that is required.

Your Aero-Lift is completely pre-assembled and tested at our manufacturing facility, leaving only a few components to be bolted together to make your Aero-Lift operational. The assembly of these components can be accomplished with simple hand tools. A list of the specific hand tools required is outlined in the Assembly and Maintenance Manual.

They are easier than you would think, but we will gladly put the beds together for you when we deliver in the UK. Assembly Instructions that are easy to understand are sent with our beds shipped overseas.

With our frame system, a cast-interlocking dovetail, all that you need is a hammer to set the frame. It is a drop in friction fit; there are no bolts or screws involved. It is easy to assemble and disassemble.

No. All tools and test equipment are provided for the duration of the course and it is recommended that the purchasing of tools and test equipment be done when you have completed the course. This allows you to select tools with a greater knowledge of exactly what you require.

In addition to a few basic electronic assembly tools, you will need a high quality temperature controlled soldering iron. You should also have a 3-1/2 digit digital volt meter to execute the start up tests. Additional test equipment is not required. The documentation we provide with your order is more detailed and gives suggested sources for this equipment. Check out our DIY section for suggested tools, test equipment and suppliers.

NONE. No tools needed . We have designed our garage screen for simple installation. No long complicated instructions. It is easy as 1,2,3 GUARANTEED! No problem. Our screens were carefully designed to accommodate most standard door sizes. We designed our screens to be flexible enough to fit openings that may be a few inches shorter or narrower.

Instructions and hardware are included in the headboard box - all you need is a screwdriver with a phillips head.

Yes! Actually, it's hard to imagine an easier design—you just stack the boards so the ends interlock and insert metal pins to assemble the beds. The included 3/8" aluminum pins slide easily into the pre-drilled holes. Raised beds 8' and longer include flat aluminum crossbars that fit over the pins between board sections (see right).

When it comes to tools and technology, just the combination and amount that's right for you and your job is what you'll need. Your organization may provide a list of recommended (and sometimes funded) equipment. On the other hand, you may be on your own to figure out what you need.

Absolutely no specialist tools are necessary to fit your new EPDM roof. Handyman tools such as a sharp knife, wood saw, drill, hammer and scissors are all that is needed to install the system.