NOTE: AFFECTED MODELS ONLY INCLUDE: HONDA Models EB3500XK1, EB5000XK1, EB6500SX, EB12DAG, Arctic Cat Model 1999 AC7500GD2EB and some models from Briggs and Stratton. The Honda EB (Industrial/Commercial) series generators listed above have their neutral wire bonded to the ground wire to pass OSHA inspection on job sites. Since home and building main load centers also have the neutral bonded to ground, a loop is created, comprised of the neutral wire and the ground wire.

Certain Honda Industrial/Commercial generators have the neutral bonded to ground to pass OSHA inspection on job sites. Since home or building main breaker boxes also have neutral bonded to ground, two parallel paths back to the generator are created, one using the neutral wire and one using the ground wire. The neutral current now flows through both conductors.

A transfer switch isolates those circuits using generator power during an outage from the utility power. This eliminates the risk of back feeding the electric utility, which can cause injuries to utility workers and property damage.

First, the transfer switch you select should match the maximum continuous wattage rating of your generator. For example, if you have a 5000-watt generator, you should select a transfer switch rated at 5000 watts, such as Model 200660. You may also select a transfer switch that has a higher rating than your generator. (Ex: a 5000-watt generator with a 7500-watt transfer switch is OK.) But NEVER install a transfer switch with a lower rating than your generator.

NO. While it might be possible to connect a larger generator to the transfer switch, this is an unsafe and dangerous practice. Supplying more than the rated wattage through the transfer switch could damage the wattmeters, damage the neutral wire, and could overheat the main wiring in the transfer switch, which could cause a fire.

When your utility power is restored, lights and appliances in your home not connected to generator power will turn on; alerting you that utility power has been restored. Because Gen/Tran PowerStay? Transfer Switches have interlocking main breakers, the utility power and generator power are never powering those circuits using generator power at the same time. There is no danger of back feeding the utility power. No.

No. The Onan portable generators use a manual three-wire start/stop system with no provision for automatic starter disconnect.

This is acceptable for peak wattage but not recommended for running wattage. Pulling more than the rated wattage through the Reliance Pro/Tran? transfer switch could burn out the neutral wire, overheat the main wiring in the transfer switch and cause a fire. To insure proper safety precautions, a suitable double pole breaker should be installed between the generator and the transfer switch when the running wattage of the generator exceeds the rating of the transfer switch.

The trip switch in your home works as a safety device for your internal wiring. Faulty appliances or wiring will make the trip activate, and the trip will remain in the off position until the fault is fixed. The trip switch is located on your own consumer unit after the meter point. Your consumer unit is most likely to be in the garage, hallway, kitchen/utility room, under the stairs or in the toilet.

A Ground Fault Circuit Interrupter detects tiny amounts of stray current and shuts off the electricity before it can cause harm. A GFCI is much more sensitive to a problem than a fuse or standard circuit breaker.

The average time scale is two to three weeks. We ensure that every transfer is expedited as quickly as possible. However, it should be noted that the transfer cannot be started until we receive the required documents. Please note that whilst we take all reasonable care of your documents, we cannot expect any responsibility for their safety once passed into the hands of the Department of Transport, although it must be said that it is extremely rare for them to lose documents.

Answer: You may request to transfer up to 9 graduate credits from an accredited university. These courses must have been completed within the past 10 years. Approval is determined after evaluation by the Program Director and the Assistant Dean for Academic and Student Affairs of the School of Health Technology and Management.

You everyday standard 7 page site will almost definitely contain some of the following Home, Why use us?, About Us, Clients / Testimonials, Services / Products, News, Partners and a Contact Us page. This is the standard, but this should NEVER deter you from going down a different path, just ensure your sites information flows easily and makes sense all the way through.

A transfer switch is a panel that is wired into the premises electrical distribution system to allow a generator to be used. It prevents the generator from back feeding into the mains power supply which could cause serious injury to line workers trying to restore utility power supplies.

If you have any other questions about web sites, contact Screaming Iguana at 512/732-7369 or send us email.

Absolutely! Our generators are PRBS generators, but with lots of bells and whistles for those who wish to use them (like developers of wireless and spread spectrum systems). But if you use only the PN Sequence output port (TTL-compatible), you're guaranteed to get a simple pseudorandom sequence.

GFCIs constantly monitor electricity flowing in a circuit. If the electricity flowing into the circuit differs by even a slight amount from that returning, the GFCI will quickly shut off the current flowing through that circuit. The advantage of using GFCIs is that they can detect even small variations in the amount of leakage current, even amounts too small to activate a fuse or circuit breaker.

The neutral wire from the spa to the breaker box must be wired into the breaker itself and not the bus bar. This is because it is not a dedicated 240v spa. If the neutral is wired to the bus bar, the breaker will instantly trip at power up. Refer to wiring diagram. The installation of all spas must be in accordance with national and local wiring rules. Always have a licensed Electrician perform the electrical installation.