Your guardrail system is extremely durable. It is made of rugged 12 gauge steel and fully welded at all connections to provide you with years of durable use. Your system also has powder coat paint which is extremely durable against corrosion and inclement weather. The powder coat paint is actually baked onto your guardrail system providing complete coverage. It is also safer for the environment.

The guardrails were designed for ease of assembly. The fact that they are easy to assemble and install allows you and your workers to focus more on the job at hand. Each guardrail box comes complete with an instruction manual. These instructions provide not only worded instructions but also diagrams of your guardrails for you to visually see how they are assembled and attached to the roof or flat surfaces. See similar questions...

Fences fronting the property should not exceed a height of one (1) meter from the natural grade line. See similar questions...

Both the HP and HS (at the tall height) are designed to fit in a standard 8 foot ceiling (about 7 1/2 feet). The HS has a short ceiling setting at about 6 1/2 feet. See similar questions...

Age 11 and minimum of 48 inches tall. We may require a riding lesson for youths based on our discretion. See similar questions...

Grass over 6 inches tall is a violation of the Housing Code and is classified as a minor misdemeanor. See similar questions...

Bryce looks about 5'7" to me or taller...may be the heels. either way shes adorable. i think its common to adjust actor/actresses hights to accomodate rolls About two years ago, I saw Jennifer on the beach (South Beach. I stood next to her briefly and walked behind her for a short distance and she wasn't taller than me...I am 5'4 (barely) and I weigh 116 pounds. Jenn has to weigh at about 130-135 pounds. She was thicker than me all over and of course a lot in the butt. See similar questions...

There are two prefered points to measure vehicle ride height. Both measurements should be taken on a level flat surface. One is at the center of the fender well to the ground.The other is at the bump stop to the axle housing or frame.. See similar questions...

Good question. A patient may also have scoliosis or severe contractions that prevent a true height measurement. There are (at least) three methods that may be used to estimate height when actual measurement is not possible: knee height, forearm length and demi-span. This is caused by missing or improperly installed dDoc print preview engine. Please reinstall from the CD, or download from the web site. This error too is caused by missing or improperly installed dDoc print preview engine. See similar questions...

No!! We do not maintain a height and weight requirement. We do require that all potential members maintain the appropriate physique in order to participate in the required movements. See similar questions...

A handful of celebrities have unpromptedly submitted their height, or asked to change a listing, which I of course will do...unless you happen to be Tom Cruise insisting you're really 5ft 10. There's a limit to my belief! Any communication is treated in confidence. See similar questions...

The top of the net, along its whole length, is 15.25cm above the playing surface. The net is suspended by a cord attached at each end to an upright post 15.25cm high, the outside limits of the post being 15.25cm outside the side line. The bottom of the net, along its whole length, should be as close as possible to the playing surface and the ends of the net should be as close as possible to the supporting posts. In official tournaments players can only use their own racket. See similar questions...

Yes. The top of the monitor should be at eye level because the eyes are at their most comfortable position straight ahead but slightly downward. This is why reading lenses in bifocal glasses are placed just below the horizontal plane. This posture also makes it easiest to balance your head above your shoulders with the least muscular effort. See similar questions...

It is most important that seat height should allow the upper body postures described in #7, #8, and #9. This upper body posture is most responsible for reducing risk of injury. Once this is accomplished, the feet should be flat on the floor. If the resulting seat height prevents the feet from resting flat on the floor, a foot rest is necessary. Even a phone book can serve as an inexpensive solution. This should allow the lower legs to be vertical and thighs horizontal. See similar questions...

Each fixture has a counter weight that slides up and down. Some models come with spring loaded locks at the ends of the counter weight, depress the locks to release, then pull up and down to adjust the height. Care should be taken not to kink or twist the cables, as they are low voltage conductors as well as support cables. See similar questions...

What we have is listed in the Ramps Section of our site. If you don't see exactly what you want let us know what you wanted and we'll work on getting plans for the most popular requests. absolutely! We're hoping this site will encourage you to document your ramp, so that others can learn from your experience, and get ideas for their own ramps. if your site has good ramp making information then we would be glad to link to you. See similar questions...

Most HPI car and truck kits come with optional ride height adjustment clips. These clips are shaped like a "C" and have a small tab that you can hold with your fingers or pair of pliers to remove them. Use these clips to raise the ride height, and remove them to lower the ride height. In general, casual R/C car owners should be able to fit one finger under the front and rear of the car's chassis, or have about 7mm or 1/4" ride height. See similar questions...

The county's Zoning Ordinance regulates the location of fences and walls on a lot based on the height of the fence or wall. On most residential lots, the Zoning Ordinance only allows a fence or wall of 4 feet or less in the front yard. Remember that on corner lots, the two yards which lie between the principle building and the intersecting streets are both deemed to be front yards. In a side or rear yard, a fence or wall of not more than 7 feet is generally allowed. See similar questions...

The cutting height on the DR? TRIMMER/MOWER can easily be adjusted in half-inch increments from 1-1/2" to 4". Adjusting the cutting height is as simple as inserting the cord on the trimmer head at the desired height that best suits your trimming and mowing needs. The DR? arrives with its cutting height set at 1-1/2"...the most common height for lawn mowing. See similar questions...