Probably. Any wireless receiver supporting the industry standard 802.11b or 802.11g protocols should work. However, in rare cases, we have found wireless receivers which had compatibility issues with the computer upon which it was installed.

A USB cable and the presence of USB connections are not yet adequate for exchanging data successfully. However, data transfer can be effected using a USB cable if a serial COM Port is emulated by the GPS receiver. The GPS data must be available in the NMEA 0183 format when data is called up online, so that Geogrid is in a position to evaluate these data.

Navtex receivers can be connected to NaviGator. Again they need to have the following pin connections: Pin 2 - NMEA / Position In, Pin 3 - NMEA / Position Out, Pin 5 - Ground. Once it is connected and messages are being received and they have a Lat and Long, they will be displayed on the chart for you to click on and view the message.

We provide an installation manual with step-by-step instructions. FSL equipment is designed for a wide range of interfaces and relays. For special applications, FSL can provide special interfaces.

To connect the audio output from the computer to the AV receiver, you need a stereo mini-plug to a stereo RCA pin cord. Then connect the line-out from the computer sound card to an available audio input on the receiver. Select the input and adjust the volume output from the receiver.

You will need to buy a 3.5mm ended to a RCA stereo cable from an electronics store. Hook up via the audio 3.5mm out to the receiver audio in.

The phone line connected to your receiver(s) ensures your ability to purchase Pay-Per-View movies and events . It is also required so your receiver's may be updated with the latest software. If you do not have a phone line, there will be an additional $5 per month charge per receiver. The DISH antenna is 20 inches and complies with the Satellite Consumer Bill of Rights, a regulation released by the FCC on August 6, 1996.

No. A DA1920SX transmitter requires a DA1921SX receiver, and a DA1931CT receiver connects to a DA1930CT transmitter only. The main reason is how the video signals are encoded in the transmitter. DA1930CT + DA1931CT provide superior encoding algorithm and signal quality for video transmission.

The speakers incorporate the Direct/Reflecting technology that not only ensures you get a stereo sound throughout the listening area and not just the sweet spot as in the case of conventional speakers, but also deliver a richer and lifelike performance. The Acoustimass technology helps deliver rich pure bass with no audible distortion.

Many new PCs (especially laptops) have USB ports but do not have the standard 9-pin serial ports found on older computers. This presents a problem because most of the GPS manufacturers don't make data cables that terminate with USB plugs. Unfortunately, we have noticed that the USB-Serial converters often cause computer crashes. We are working hard to resolve this problem.

While the Co Pilot will operate with nearly any current radio system without requiring any other peripheral items, there is one exception. Certain current model Futaba PCM receivers and possibly a few JR models may experience interface problems with the Co Pilot. Here's why: some current model PCM receiver output servo data to the servos in parallel (at the same time).

The receiver will have an HDMI connector (High Definition Multimedia Interface) as its primary means of connecting to an HD display. HDMI can also be connected to DVI equipped displays using a suitable adapter cable. Most HDTV content will be protected by HDCP (High-bandwidth Digital Content Protection). This means most HDTV content will only be able to be viewed on display devices that have HDCP software built into them.

You typically have two options when connecting a powered sub woofer. Input (1) on the rear of the sub woofer would be used when connecting the sub woofer to the receiver using speaker wires. You would then connect the main speakers to the opposite end, or output or the sub woofer to the main speakers. Option (2) would be using RCA line level output jacks, input (2) on the rear panel of the sub woofer directly to the single sub woofer output on the back of an AV receiver.

In most cases, your TV may only have one set of video inputs. If this is the case then you are limited to the amount of video product that you can connect to the TV. By connecting all your audio/video components directly to the receiver, you would only have to use one video cable from the receiver to the TV. This in turn simplifies the connections, which makes video switching easier.

Yes. The speakers on your hi-fi set are probably better quality than the speaker on your television ­ even if it is a stereo television. If you have four or more speakers, then you can get the full cinema experience in your own home from films with surround sound audio tracks. Your qualified installer will advise you and carry out the connection.

Please visit the appropriate IntelliGolf Tour (i.e. on-line manual) for more information on setting up your GPS receiver with IntelliGolf. They can be found by clicking here. Section 6 covers this topic (i.e. IntelliGPS). Also, there is more information on (generally) how to connect/bond your Bluetooth-based GPS with your smartphones in this this PDF file.

A Receiver is the person(s) appointed by the Court or under a Deed or Agreement to realise assets or manage the business of a company for the benefit of the security holders. The Act defines the qualifications of a Receiver.

If your current receiver has no subwoofer (RCA) line level output, you will need to connect the subwoofer to your receiver using speaker wire connections on the rear of the receiver. You first need to take the speaker input from the subwoofer to the A or B speaker terminals on the rear of the AV receiver. Then take the speaker outputs from the sub woofer and connect to the main speaker terminals inputs.