The term Ohms-cm (Ohms centimeter) refers to the measurement of the "bulk" or "volume" resistivity of a semi-conductive material. Ohms-cm is used for measuring the conductivity of a three dimensional material such as a silicon ingot or a thick layer of a material. The term "Ohms-per-square" is used when measuring sheet resistance, i.e., the resistance value of a thin layer of a semi-conductive material. See similar questions...

The unit of measurement when measuring the resistance of a thin film of a material using the four point probe technique. It is equal to the resistance between two electrodes on opposite sides of a theoretical square. The size of the square is unimportant. See similar questions...

It doesn’t matter. Ohms per square is the unit of an electrical measurement of surface resistivity across any given square area of a material. It is the measurement of the opposition to the movement of electrons across an area of a material's surface and normalized to a unit square. This measurement is intended to be a basic material parameter and not dependent on absolute area, length or thickness. See similar questions...

Very easy. 100 square meters is 1076 square feet. Surfaces are given in square meters, written m2 or m2. See similar questions...

Each 54 in. fabric yard is equal to 18 sq. ft. of leather. Each 50 sq. ft. hide is equivalent to 3 - 3.5 yards of fabric that is 54 in. wide. See similar questions...

Well, probably. The MA 6S will not be damaged but you will obtain much less power output, and an extremely hot amplifier. To protect itself the MA 6S will current limit to the best of its ability. The MA 3 will current limit also and its fan must be set to high speed. Be forewarned that running below rated impedance voids the warranty and may damage the amplifier channels as well as power supply. See similar questions...

The unit of measurement when measuring the bulk or volume resistivity of thick or homogeneous materials such as bare silicon wafers or silicon ingots, using the four point probe technique. RESISTIVITY is the inherent property of the material which gives it electrical resistance. It is sometimes called Specific Resistance. Sheet resistance is the resistance of a thin sheet of material which when multiplied by the thickness (in cm) gives the value of resistivity. See similar questions...

To have a US item run under UK current you need to buy a transformer, a product that you plug into the wall and has a US-style jack at the other end. The transformer will "step down" in voltage from 240 to 120v. From there you may want to plug in a US-style power strip and provide current for sev eral products. Next you need to consider how many watts your transformer is providing (all transformers should clearly indicate this). See similar questions...

By best approximation, to get sq. meters, divide sq. ft by 10.75, or multiply sq. meters by 10.75 to get sq. ft. The conversion rate is currently 44 INR to one dollar. This is a fluctuating rate. Divide INR by 44 to get close approximation of prices in U.S. dollars. To get the current rate go to: http://wam.org. See similar questions...

Impedance is the load connecting to the speaker socket on the amplifier or combo to give maximum power transference. This must match the stated impedance value on the amplifier or combo to ensure no damage can be caused to the speaker or amplifier. See similar questions...

A standard square is 15 inches on all sides. A square can be made from the back, front, or both sides of a t shirt, sweatshirt, jersey, etc. It can also contain anything you want us to sew onto a 15 inch blank square, such as sweatpants, jackets, boxer shorts, towels, etc. Back to top See similar questions...

Well lets see? Put simply, Ohms is the measurement of electrical resistance and system impedance. It is a measure of the degree to which electrons are limited in both velocity and quantity in passing through a circuit. In Impedance measurements, this takes into account, the mechanical resistance inherent in the motion of transducers. The standard is usually 4 ohms for car audio and 8 ohms for home and commercial audio. Some specialty woofers may be rated at 2, 6, 12 or even 16 ohms. See similar questions...

No. There will be no licensed food and beverage vendors in Times Square. However, there are hundreds of restaurants in and around Times Square (see below). Many restaurants located in the Times Square area will be open on New Year's Eve - be sure to consult our Interactive Map and Guide to locate a restaurant - and make your reservations well in advance. See similar questions...

Since Sacred Harp singing is a participatory activity, and not a performance, the singers arrange their seating so as to focus the sound inward, toward the center of the group, instead of projecting it outward toward an audience. The greatest volume and optimum balance are heard in the very center of the hollow square, where every singer may take his or her turn as leader. See similar questions...

It may not be possible to achieve any DSL service at 1500 ohms (18 kfeet of 26 AWG) without TripleStream. With TripleStream on properly qualified plant, data rates in excess of 3 Mbps are possible. See similar questions...