Make sure that bobbin case and spring are clean before beginning this procedure. This is to ensure consistency once proper tension is set. Pull bobbin from under hole of tension spring. If bobbin case has a middle thread guide or pigtail, do not thread through at this time. Hold the bobbin by the thread hanging out of the case to check the tension. The ideal tension should be when the bobbin does not move, or is very slow releasing thread.

In most of the cases you get good results when setting the tension loose: "when you hold onto the bobbin thread and let the bobbin case hang, it should begin a slow but steady drop." See similar questions...

Do not force belt over sheave grooves. Slack off drive for easy mounting of belt. Align and adjust drive so that belt operates free and clear of all obstructions. Belt tension is highly important. When in operation both tight and slack strands of. the belt should be in a straight line from sheave to sheave, and with no sag or bow. Check belt tension after eight hours operation, followed by periodic inspections to be sure belt is under sufficient tension and that belt is not slipping. See similar questions...

The mirror sling has two purposes. The first is to prevent the mirror from rotating, which would shift the triangles from being centered over the collimation bolts. The second is to lift the mirror up off the lower two cell posts. This provides a nice even support for the mirror and allows the mirror to follow the collimation bolts when they are backed off, rather than being held by friction on the lower posts. See similar questions...

Answer with ease that in any job and any situation that tension is a part of it. Relax before putting the f act you are very used to such type of works. See similar questions...

Your chain tension is set correctly is when the chain is as tight as possible, but still moves freely around the guide bar. To check your chain tension be sure that your bar and chain are lubricated with bar & chain oil. Then, wearing gloves or using a rag to protect your hands, grab the chain on the top rail midpoint of the bar and the bottom rail midpoint of the bar. Aggressively pull the chain back and forth several times to be sure it is seated properly. See similar questions...

Depending on where you live, tension can mean knitting gauge or it can have to do with the openness or tightness of your knitting. Gauge is important because how your stitches look will influence how the finished knitted item looks. See similar questions...

Much like you, when we first saw this design technique years ago, we were concerned with its securing capabilities. However, once the designer insisted that we try to pry the diamond free, it became apparently clear that it could not be done. So yes, this diamond is absolutely secure. In fact, the ring is made around a specific diamond and secured under 65 to 95 pounds of pressure. See similar questions...

Fine tuning the correct amount of tension on a Rubber Belt is largely a function of experience. Several variables, including the current thickness of the belt, the style of fabric being processed, etc., need to be taken into account for an accurate determination. In general, however, the proper tension on a 67 mm (2 5/8") thick Rubber Belt can be approximated as follows: With the rubber blanket tension set at the minimum position, draw two (2) lines*, 30. See similar questions...

Please click on the link below to download a PDF. (Adobe Acrobat Reader required. If you don't have Adobe Acrobat Reader, click here.) Tensioning the Running Belt Back to top See similar questions...

If excessive slack exists, adjust cable tension by removing the pulley bolts and moving one or both pulleys to the inner mounting position in the dual floating pulley bracket and then reinstalling the pulley bolts. Cable tension may also be adjusted using the threaded cable end on single pulley bracket and weight stack. Twist threaded end to adjust tension and then tighten lock nut. NOTE: Always maintain at least one-half inch of threaded bolt in bracket. See similar questions...

Are you looking for more distance on your shots or more control over them? Generally, if you string at the lower end of your racquet's recommended tension range, the same stroke will make the ball fly farther. Adjust string tension according to desired effect. Low tension = deeper shots. High tension = shorter shots. any given swing speed, higher string tensions improve control. High tension = better control. Low tension = less control. See similar questions...

Click here to view a movie clip demonstrating how to cleaning lint from the bobbin case area. It also demonstrates inserting the alternate bobbin case. See similar questions...

No. In fact, I will not run 12 wt both in the top and bobbin. It is simply too much thread to fit through the clearances around the shuttle. The rest of the Sulky lineup of threads can be exactly matched, but many times I will choose a finer weight of the same thread because more of it fits on the bobbin. I prefer 40 wt. Rayon or Poly Deco in the bobbin when running Holoshimmer, Sliver, or Metallic in the top. See similar questions...

When you buy a Re-arm kit, ensure that the "install by" date printed on the package has not been passed. If the "install by" date is not legible, check the manufacture date printed on the bobbin and ensure it is not older than 3 years. If installed in an inflatable PFD with a 1F Inflator, the bobbin should be replaced at least every three years in case of recreational use and at least every 2 years in case of commercial use, or more often in extreme conditions (i.e. See similar questions...

Some times tension and migraine headaches occur from conditions you are not aware of. Here are some areas that cause headaches and what you can do to eliminate these sources. Here is some information you need to know about remedies for heartburn. Your first step in dealing with heartburn is to stop creating it. Here are some tips you need to know to do that and two natural remedies that can cure your heartburn. See similar questions...

Opinions differ on this topic, but here's mine... I belive that the tension should be high enough to keep the blades from shifting their lead/lag angles at low rotor speeds (e.g. autorotations), but not so high as to put excessive stress on the blade grip and blade bolt, nor so high as to keep the blades from finding their proper lead/lag positions. Try holding the helicopter with the nose pointing straight up and the blades sticking out sidewise. See similar questions...

Tension occurs mainly when you are overtrading and have no rules and stop losses. Refer to Trading Rules See similar questions...