This is largely a design choice. If your heaters are standard height, we recommend that you order your wainscot with a base height 1-3" above the heaters. If they are tall, like older ones that are sometimes 24" tall, we recommend that you just ignore them for ordering purposes. During installation, you will just cut around them.

The dirt streaks that are being created above your baseboard are mainly dust, dirt, and carbon soot that might come from fireplaces, water heaters, furnaces, standing pilot lights, candles, cigarette smoke, cooking byproducts, and even automobile exhaust by the natural convection that occurs during the heating cycle.

Yes. You can now find programmable AND more accurate thermostats made especially for baseboard heaters as most home improvement or hardware stores. But before you go, find out if your baseboard thermostats are single-pole (two-wires coming in from the wall) or double-pole (four wires coming in from the wall). Most are single-pole and not always interchangeable. (A double-pole thermostat will have an "Off" setting.

Here is one way of doing it, a picture ready is worth a thousand words. If you have allot of baseboards to work with we suggest that you order a few extra lower rails (PW-8) and the router bit to customize the stiles on site easily.

Yes you can. All you need to do is provide a Radiantec mixing valve to step down the temperature of the water to the radiant circuits. You mix hot water from the boiler with return water from the floor to provide a lower temperature.

Pure ceramic. There is a hair-thin wire filament running through it. Our Pure ceramic heaters are made specifically for SaunaRay. They have a concave shape which allows the edges to fan-out the waves and the heat to cover a larger area. The Stainless steel reflectors are mirrored and made out of 100% surgical grade stainless steel. They reflect the far infrared heat even wider, ensuring a complete 360 degree coverage inside. You are surrounded by far infrared heat!

The factory installed propane furnace does a pretty good job of keeping the pop-up warm, but you WILL go through a lot of gas. A normal 3 day weekend with evening temperatures in the 30's or 40's will use a full 20 lb tank of LP gas. If you're camping on an electrical site some people suggest taking along a small electric heater as well ... it will allow you to cycle the furnace off a little more and thereby us less gas.

There are tools designed especially for this purpose. The Super Guide by Hyde? Tools is a metal shield that can be placed between the carpet and the baseboard allowing you to paint one section at a time. Another method is taping the carpet with masking tape or masking paper.

No, the system generates low temperature heated product that works well with radiant floor heating systems, warm air heating, Solar Domestic Hot Water (SDHW) heating systems and other types of low temperature heat distribution systems.

A piezoelectric switch (pronounced peezo) contains a crystal that exhibits piezoelectric properties. A piezoelectric crystal converts mechanical force into an electrical voltage, hence, you press the button and an electrical charge is used for ignition. If you have ever started a gas barbeque you have used a piezoelectric switch. Continuous electronic ignition is a constant spark generated from an electrical source. It keeps sparking as long as the heater is on.

Most FIR sauna heater elements are steel-coated. Steel coating is an older technology that directs the heat source but requires more time to warm up, operates at higher temperatures, and uses more energy to reach the level necessary for deep tissue penetration. Now, ceramic-coated heater elements result in lower temperatures and more efficient energy use. Ceramic-coated FIR heaters produce the same useful energy as the sun at a very safe (.

A baseboard heater requires 30 to 60 minutes to heat the room, provided the heater has been properly sized (adequate wattage) for the room. Baseboard heaters are longer, but not as tall as a fan heater. For example, a 1500 watt baseboard will require 6 feet along an outside wall and is about 7 inches tall. A Register Plus heater grill is 14 inches wide and 7 inches high. Baseboard heaters operate at lower temperatures, making the surface temperatures of baseboards cooler.

With the exception of the outdoorsman model which can run from a 20 lb tank, the indoor gas heaters require a 100 lb because of the speed at which the gas flows to the heater. The faster the propane flow the colder the propane gets (experience this by blowing air gently from your mouth to your hands, then blow some air as hard as you can into your hands - the faster moving air is colder than the slower moving air).

Natural corrosive properties of all waters will eventually cause the unit to fail. The time it takes to have the heater fail depends on the minerals in the water and how hard the water is. We partially soften the water to reduce corrosion in the water mains, hot water heaters and in household plumbing.

Answer: Space heaters should be acceptable provided they are permanently affixed, properly vented to the exterior or have an oxygen depletion device, and are in accordance with local codes. Also, the appraiser must make a determination whether or not the space heater provides sufficient heat to the room(s) where it is being used.

The band heater is a 3/8" wide stainless steel hose clamp placed around the cylinder, and it will dissipate heat just as well as the cylinder itself. During the development stage we discussed the idea for this cylinder heater with Rick Moffet, Lycoming's VP of Engineering. We specifically discussed the cooling issue, and he had no concerns about cooling. He said the lower end of the cylinder where the band is installed does not generate heat like the top end where the combustion occurs.

Occasionally we get this question from someone who fears that heating the cylinders is bad because it may allow the oil in the cylinders to run off, so the cylinders may be "dry" when the engine is started. This is not a concern, because: Our cylinder heaters raise the cylinder temperature about 70-90o above ambient, like a warm summer day. So oil runoff is no more of a concern when preheating than it is when your aircraft is sitting on a hot ramp in summer.

If you purchase a product that you do not like, you can return it at your expense back to the shipping address. There will be a 10% restocking fee. Please allow one business day to arrange for pickup at our Ontario, CA location. No further discounts apply.