screws to the ceiling surface. The wiring compartment has a standard size knock-out on top and is 3” in Yes. socket sets are supplied in 6 foot lengths and may be cut to a desired length; follow the detailed instructions supplied with the socket. No, doing that can harm the other transformers. Remove the inoperative fixture immediately. Take one of the operating units and install it in the inoperative location.

Yes. We recommend an electronic low voltage dimmer. Where a remote transformer is used, dimming can be accomplished by utilizing a dimmer to match transformer type (e.g. low voltage magnetic dimmer with a magnetic transformer).

Absolutely! You can install either type in any in-wall or in-ceiling applications. Footprint size and aesthetics may be a consideration. In-Ceiling speakers are smaller and have a smaller footprint (or overall dimension). However, the larger In-Wall speakers will mount safely to wall or ceiling. Either speaker can be used for either application. Typically, most rooms will only need a single pair of speakers to provide adequate coverage for background music or moderate listening volumes.

Yes, unlike other brands where a specific trim is designed for a specific housing, any one of the three trims will fit the sloped ceiling housings.

Use the Architectural Objects (Ceiling Objects; Ceiling Obj. #1) to mimic the slope of the ceiling, following the rise-and-run of the slope. The Basic Objects can also be used to model the horizontal and vertical components of the stair-step affect required to model the sloped surface.

Most manufacturers offer an optional "sloped ceiling" adapter that will allow you to hang your fan at any angle up to 48 degrees.

Not all projectors can be ceiling mounted. If you need this feature, ensure the projector supports ceiling mounting.

define a new orientation for this orientation/slope in the TrnBuild "Project Initialization" window, and use it for the wall the window is in calculate the orientation / slope with a type 16 / 109 (solar radiation processor) and connect it to type 56. All surfaces are assumed to be black for long wave radiative exchange and radiative internal gains for surfaces inside the zone.

This can be done, however the CNK200 requires wall that is thicker than normal 4" wall. (Please verify this information with out Technical Support Department since the total thickness from the bezel's bottom edge to the last hinge for table-mount bracket attachment looks to be less than 4" as per the diagram posted on our website.) The termination switch should be ON if the local monitor is connected through a straight cable.

Our full range can be seen at our showroom and workshops in Iwerne Courtney near Blandford in Dorset, which is open by appointment. Your local agent would also be delighted to show you samples.

Yes, you can. For detailed directions, look up the owner's manual or wall-mount kit instructions, because all such models can be easily wall mounted. Such kind of intermittent issues can prove to be very tricky. I would recommend contacting both your dealer and the Sony technical support team in order to avoid problems that may crop up in future. From your description it is tough to understand the possible issue with your TV set.

I've installed all the filters and plugged in the DSL modem but I'm not getting any internet connection. The "Ready" light is blinking. I've removed all the phone devices from their respective phone jacks and only have my DSL is connected but the Ready light is still blinking.

No attachment is necessary when using the compression kit to secure the pole in place. The shelves go between the poles and the wall and do need to rest up against the wall.

Although the ISS Designs shelving is described as a sleek minimal system, it is also strong enough for most medium weight requirements. That means it is great for your office, family room, den, kitchen, pantry and more.

The wall-mounted remote is a transmitter that communicates with a receiver in the fan canopy via radio waves. The remote comes with a standard size switch plate (the same as any light switch) and can be mounted on the wall in any location that has electrical power (the remote does not have to be mounted on the same electrical line as the fan). IMPORTANT: The wall remote MUST be wired in series. Please follow installation instructions very carefully.

Manablocs can be flush mounted right out of the box. For recessed mounting, a MBB2 mounting bracket is available (for studs spaced 16" on center).

Yes. Our LCD/TV monitors can be wall mounted. However depending on the model, the speakers might be built into the stand. Hence, in order to have the sound output, external speakers will have to be connected to the monitor - which can be done easily.

I am not sure what bin I have here, now. Can I tell if it is an Original No Butts Bin? It seems to have had a fire.