Look on the back of your CPU. There will be a jack, shaped like a phone plug-in, but it will be a bit wider than an ordinary phone jack. See similar questions...

Yes, you will have to register twice: once for the wired Ethernet connection and once for the wireless connection. See similar questions...

The wireless modem connects to your computer via a USB or Ethernet Port. You need to check which of these you have free on your computer before you order your Unwired modem. These ports are usually located at the back of the computer. You can find pictures of these on the System Requirements section of the Unwired website. Your computer's USB port allows you to connect external devices (such as printers, digital cameras, etc) to your computer. See similar questions...

External adaptors are available for both desktop and laptop computers which connect to either a USB port or PCMCIA card slot. See similar questions...

The WLA660's Ethernet port (RJ-45 jack) supports 10 Mbps over a 10Base-T connection (half-duplex only). See similar questions...

ITS's networking group does all new port installations and activations. Please call ITS at 962-HELP or open up a ticket at http://help.unc.edu. You will need the following information: building name, floor, room and port number(s). See similar questions...

You have several options. You can purchase a Network Interface Card (NIC) at any computer supply store. This will require a physical installation of the card into your computer. Or you can purchase a USB-Ethernet adaptor which converts a USB port on your computer into an Ethernet port. We have USB-Ethernet adaptors in stock for purchase and delivery with your modem. See similar questions...

Either one will work with the cable modem and service Wave provides. However, not all computer systems allow for a USB installation. Before your Internet installation, you must have a computer with a USB port, or have a 10 Base T Ethernet card installed in your computer. See similar questions...

The outer sleeve will have a sticker that indicates the connection type. The USB port will be to the right of the power jack on the back of the Unwired modem. The Ethernet port will be diagonally across from the power jack. See similar questions...

When ETH connector (green) = ON, good receive/transmit on the Ethernet port. When ETH connector (orange) = ON, good physical connection to Ethernet segment. See similar questions...

On the SU that you want to deny customer access to, turn on IP filtering, and simply filter out the address or subnet that the customer is using. Configure the "User Defined IP Address" table to an IP range that is not in the range or subnet that the customer is using. When configuration changes seemingly by itself, this indicates there is a hardware problem with the unit. If warranty still applies, contact Alvarion tech support to RMA the unit. See similar questions...

A. The Targus USB Mobile Port Replicator with Ethernet is the world’s smallest expansion hub that provides instant peripheral device attachment and Ethernet via a single USB connection to Windows 98/ME/2000 based computers. Packaged in a small and attractive enclosure, the PA090U can fit any place on a desktop space. Add devices like mice, keyboards, joysticks, network, printers, PDAs, scanners, speakers, cameras, telephones and many more without rebooting your computer. See similar questions...

Please note: It is usually a bad idea to force the speed of an interface. If possible, leave in Auto-negotiate mode. Contact support@candelatech.com if you have questions. LANforge supports setting the ethernet port speeds through the GUI and CLI. The CLI Scripts page offers the lf_verify.pl script that has an example of setting the port speeds through the CLI. Information on how to set it through the GUI can be found in this section of the LANforge GUI Users Guide. See similar questions...

Unfortunately, this switch is defective. Please go replace you switch ASAP with your Vendor. If you have this switch over 30 days, then please E-mail rma@gigafast.com for future instructions. See similar questions...

Some DSL modems carry USB capability. This is useful alternative in instances where a network card cannot be installed. Please note that you cannot use the USB port of a usb HUB to extend the wire length between your modem and PC, or share the access to multiple systems. You can use the USB and Ethernet ports at the same time to facilitate access on two machines provided the advanced modem routing features are enabled. See similar questions...

USB ports have been popular since the year 2000. If you computer is older than this, then you may not have a USB port. Also, USB support is only available on Windows ME, Windows 2000, Windows XP and Windows 98. USB support is not available on the first version of Windows 95 or on NT. It is available on SR1 of W95. The plug that goes into the USB port looks like this: A game port is usually found on your sound card. It is a 15 pin, female connection. The 15 pins are split into two rows. See similar questions...

Most computers sold today come with an Ethernet card already installed. If your's did not, ou can print the Installation Guide and install the card yourself, or you can contact the Help Desk, who may be able to walk you through it. See similar questions...