Doors with extension springs require 10" of headroom while doors with the patented EZ-SET® Torsion Spring System require 12" of headroom. If installing a garage door opener, you will need an additional 2 - 3 1/2" of headroom depending upon the brand of opener. Low headroom hardware is available at your Holmes retailer to reduce the headroom requirement to as little as 4 1/2". Again, this Web site can help you determine these exact measurements. Click here to link to our convenient worksheet.

Everything needed to install your screen is included. Hook and self-adhesive loop fastener, screen, and directions.

This depends on what type of spring system that your new door will have. For extensions springs, a minimum of 10" is required for the door to operate. Torsion springs require 12". Remember, these amounts are for door operation only. If you are installing a garage door opener, additional headroom is required. Check with the opener manufacturer for additional headroom requirements.

The tools you will need to install your door include: jig saw, drill with 1/8", 1/4", and 1/2" drill bits, screwdriver, wire cutters, long nail and pencil. There are some other tools that aren't necessary, but a good idea: ruler, bubble level, and a carpenter's square.

The first time the Garage Door Screen is installed, it might take 30 minutes to install. After that, it takes only a minute or so to put up or take down.

Newer refrigerators and freezers have magnetic snap-in type gaskets that are secured to the door by a foamed in place, grooved retainer strip. Beginning at one corner, pry gasket loose from retaining strip. Peel remainder of gasket from door and discard. Before replacing, be sure the gasket and door are at room temperature. (If necessary, soak the gasket in warm water to make it more pliable.) Align new gasket frame on door retainer strip.

I am wondering about zoning constraints related to residential dome structures within an urban environment.

Injury: Installing a garage door is dangerous. Because of the extreme spring tension involved, many novices have been seriously injured or even killed by garage door accidents. Time: It's not uncommon for a novice to spend all day installing a door, while a professional can do it correctly and safely in an hour or two. For these reasons, we urge you to have a qualified door mechanic install your door, and call him again when your door needs repairs or adjustments. It's money well spent.

The hole that needs to be cut varies from size to size. The openings that need to be cut for each size are: Small 7-3/8" by 10" high, Medium 11-7/8" by 15-3/8" high, Large 14-5/8" by 20" high, and the X-Large 17-15/16" by 22-9/16"high. To aid in installation, the door comes with a template for the hole size.

Holmes recommends that only experienced do-it-yourselfers tackle installing a garage door. DIYers should enlist the help of at least one other person when installing a garage door for the first time. Common tools needed for installation are screwdrivers, wrenches, a power drill and a stepladder. Depending on the skill level of the DIYer, installation can take 8 – 10 hours.

Punched angle for rear track hangers and automatic opener - 1 _" x 1 _" minimum (angle at least 13 ga. or 3/32" thick.)

If the suspended ceiling system is being installed in conjunction with the door, our recessed hat channel can be used to facilitate installation. If suspended type ceiling is already in place a common method of installation is to place a finished board (1" x 6") on the underside/room side of the ceiling and a similar board above. These would be fastened together forming a sandwich with the acoustic material between. Drop wires or rods would be installed from above to support the door and plates.

Windsor Republic Doors and DASMA (Door and Access Systems Manufacturers Association) always recommend that a professional installer perform all installation and/or service work. Garage doors are large heavy objects under high tension. Mishandling can cause serious injury and further damage to your door and garage.

Wood working shops that are attached to the house, in the garage or in the basement generate and transmit a high level of unwanted sound into the house, home office or general living quarters. One of the biggest avenues for sound transmission is through the adjoining door. The HSDJ Door Jacket provides an additional sound blocking barrier and a bottom door sweep reducing unwanted sound transfer into the living quarters. Model HSDJ Door Jackets are available in several different sizes.

No, doors with hardware installed are difficult to handle without damage to the door or the door hardware.