The factory installed propane furnace does a pretty good job of keeping the pop-up warm, but you WILL go through a lot of gas. A normal 3 day weekend with evening temperatures in the 30's or 40's will use a full 20 lb tank of LP gas. If you're camping on an electrical site some people suggest taking along a small electric heater as well ... it will allow you to cycle the furnace off a little more and thereby us less gas.

The Vegtherm is a 12 volt inline heater. It was designed specifically to heat vegetable oil to a maximum of ~ 70 C. (assuming an inlet temperature of min. 25 C...room temperature and matching the heater(s) to the task, namely the flow rate of fuel to be heated in a specific application). Power is supplied via a relay. In "two-tank" SVO systems, it is wired so that power is supplied to the heater when the fuel selector is switched to SVO.

Most infrared heaters employ gas combustion (propane or natural gas) to heat a steel tube (tube heater) or ceramic surface (luminous heater), which subsequently emits infrared heat. It’s important to note how much infrared heat is emitted. You should also be aware that an infrared heater produces both infrared radiant heat (that is directed at people and objects) and convection heat that rises and is for the most part lost.

Biodiesel is 100% compatible with diesel #2, also known as heating oil #2, or more simply as diesel. If your heater is designed to run on heating oil #2, then it can run on B100 just fine. Kerosene, which is called diesel #1 or heating oil #1 and is thinner than diesel #2, requires experimentation. In general, if a heater is designed specifically for kerosene, then it can work with some kind of biodiesel blend (the blend being a low percentage of biodiesel and higher percentage of kerosene).

Pure ceramic. There is a hair-thin wire filament running through it. Our Pure ceramic heaters are made specifically for SaunaRay. They have a concave shape which allows the edges to fan-out the waves and the heat to cover a larger area. The Stainless steel reflectors are mirrored and made out of 100% surgical grade stainless steel. They reflect the far infrared heat even wider, ensuring a complete 360 degree coverage inside. You are surrounded by far infrared heat!

Noritz water heaters work on demand - they only heat water when necessary. When a hot water fixture is opened or hot water is required by an appliance, the heater will sense the demand and heat water accordingly. Noritz tankless water heaters continuously heat the water through a heat exchanger. Instead of wasting energy and money re-heating and storing water when it is not needed, tankless water heaters provide only as much hot water as needed.

A piezoelectric switch (pronounced peezo) contains a crystal that exhibits piezoelectric properties. A piezoelectric crystal converts mechanical force into an electrical voltage, hence, you press the button and an electrical charge is used for ignition. If you have ever started a gas barbeque you have used a piezoelectric switch. Continuous electronic ignition is a constant spark generated from an electrical source. It keeps sparking as long as the heater is on.

Most FIR sauna heater elements are steel-coated. Steel coating is an older technology that directs the heat source but requires more time to warm up, operates at higher temperatures, and uses more energy to reach the level necessary for deep tissue penetration. Now, ceramic-coated heater elements result in lower temperatures and more efficient energy use. Ceramic-coated FIR heaters produce the same useful energy as the sun at a very safe (.

With the exception of the outdoorsman model which can run from a 20 lb tank, the indoor gas heaters require a 100 lb because of the speed at which the gas flows to the heater. The faster the propane flow the colder the propane gets (experience this by blowing air gently from your mouth to your hands, then blow some air as hard as you can into your hands - the faster moving air is colder than the slower moving air).

Natural corrosive properties of all waters will eventually cause the unit to fail. The time it takes to have the heater fail depends on the minerals in the water and how hard the water is. We partially soften the water to reduce corrosion in the water mains, hot water heaters and in household plumbing.

Answer: Space heaters should be acceptable provided they are permanently affixed, properly vented to the exterior or have an oxygen depletion device, and are in accordance with local codes. Also, the appraiser must make a determination whether or not the space heater provides sufficient heat to the room(s) where it is being used.

This is largely a design choice. If your heaters are standard height, we recommend that you order your wainscot with a base height 1-3" above the heaters. If they are tall, like older ones that are sometimes 24" tall, we recommend that you just ignore them for ordering purposes. During installation, you will just cut around them.

The band heater is a 3/8" wide stainless steel hose clamp placed around the cylinder, and it will dissipate heat just as well as the cylinder itself. During the development stage we discussed the idea for this cylinder heater with Rick Moffet, Lycoming's VP of Engineering. We specifically discussed the cooling issue, and he had no concerns about cooling. He said the lower end of the cylinder where the band is installed does not generate heat like the top end where the combustion occurs.

Occasionally we get this question from someone who fears that heating the cylinders is bad because it may allow the oil in the cylinders to run off, so the cylinders may be "dry" when the engine is started. This is not a concern, because: Our cylinder heaters raise the cylinder temperature about 70-90o above ambient, like a warm summer day. So oil runoff is no more of a concern when preheating than it is when your aircraft is sitting on a hot ramp in summer.

If you purchase a product that you do not like, you can return it at your expense back to the shipping address. There will be a 10% restocking fee. Please allow one business day to arrange for pickup at our Ontario, CA location. No further discounts apply.

Unfortunately, divergent methods and opinions abound among those who install, inspect, or approve various kinds of strapping. At the root of the problem is a lack of adequate notification by the state agency responsible for the advent of current seismic standards. Since 1982, the Uniform Plumbing Code has mandated seismic safety straps for most water heaters. The purpose of this requirement is to prevent fire, explosion, or water damage if a water heater should topple during an earthquake.

Yes. You also have the added advantage of choosing the model lines and performance level that suits your budget. Moreover, the unmatched efficiency of Schwank heaters means you get quick payback. Remember, the full life-cycle cost of a heating system includes the purchase price, the fuel cost, and maintenance costs. In fact, the first-year fuel cost usually represents more than 30% of the total cost.

Yes. Most of our portable air conditioners have a built in heater. Please check the product pages for details on specific models.