The default IP address is 192.168.2.10 with a 24 bit subnet mask (255.255.255.0). Further information about initial switch configuration is available in the Installation and Getting Started Guide.

If you are using a management application like ProCurve Manager, you may be able to check on the IP address there. If you configured the switch to receive a DHCP address, (DHCP is turned off by default) you may be able to check the DHCP server for a list of leased addresses by searching for the switch MAC address (printed on the outside of your ProCurve 1800 Switch). See similar questions...

ProCurve Manager (PCM) can discover the ProCurve Switch 1800 Series, and place them on the network topology map. Once the switch is discovered, PCM can be used to launch the ProCurve Switch 1800 series Web UI. See similar questions...

No, the ProCurve Switch 1800 Series does not support any of the Spanning Tree Protocols (802.1s, 802.1D, or 802.1w). In addition to not supporting Spanning Tree, the switch will not pass Spanning Tree BPDUs (destination MAC = 01:80:C2:00:00:00) from upstream devices. Result: STP Disabled device passes the STP BPDUs from STP enabled device. See similar questions...

The 1800 Series Switches are Web Managed switches. This means that the Web interface is the only method for managing and configuring the switch. The 1800 Series Switches have a user-friendly Web interface and are designed to allow users to add basic capabilities to their without adding complexity. The 1800 Series Switches do not have a console port or command line interface and do not support SNMP management. See similar questions...

The SNMP functionality is read-only and is used by ProCurve Manager to discover and map the device. SNMP cannot be used to configure the switch or send SNMP traps to a trap receiver. See similar questions...

If you have forgotten the switch's IP address or administration password you can return the switch to its factory default state by following these steps: After completing this procedure, the password will be empty, the network address will be returned to the default 192.168.2.10, and all configuration settings will be returned to the original factory defaults. See similar questions...

The Web interface inactivity time out is 300 seconds. The purpose of the inactivity time out is for security. If the administrator logs in and forgets to log out, it will automatically log them out, so no intruder can operate the switch. See similar questions...

There is no software configuration of 802.1p for the ProCurve Switch 1800 series. The ProCurve Switch 1800 series honors priorities of the frames received. See similar questions...

The systems default and maximum parameters can be viewed by issuing the following command at the CLI: For software version 7.1.24 they are defined as follows, but these values may be different in other versions of the software: See similar questions...

YES. Using custom IP addresses and names complicates the startup, and further complicates future upgrades, as well as remote access. If at all possible, stick with defaults. There is a script file to change these but it is not foolproof and running the script file more than once can cause very undesirable results. See similar questions...

When you reset the router back to its default factory setting. The router's DHCP server function is enabled. Then you may setup a PC automatically to get IP from the Router, after you get the IP address, please use ipconfig command to see PC's default gateway address, that is the router's LAN IP address. See similar questions...

The default IP address of a PKV 40/PKV 50 is 192.168.0.160. When you have changed the IP address of a PKV 40/PKV 50, you need to cycle the power of the PKV 40/PKV 50 before the new IP address becomes valid. See similar questions...

Yes. You should always be able to open the System Setup Page, no matter what IP address you choose for The Edge server, so you can always change it. If you cannot open the System Setup Page, call CAESY Customer Support at 888-403-4003, Monday through Friday, 6 AM to 5 PM PST. Ensure that you have used the installation disc to install the required software on the operatory computer. See similar questions...

Router have their own dhcp server and can assign any computer's ip add. automatically once connected to it. Cn-550 setup ip address should be in automatic and dhcp off and let the router take over assigning the ip See similar questions...

discussed in Configuring Untangle Server as a VPN Server, Untangle Client provides you a default IP address pool (also known as virtual IP addresses). Accept the default. This default IP address pool does not match your current network's IP address scheme—which is good. This default, incompatible IP address ensures that the remote VPN clients do not conflict with non-VPN clients on the same network. See similar questions...

Yes, but this is the very nature of direct connections. BitWise bypasses the server, so your PC must know where to send the messages (i.e. what computer on the Internet). Without sharing your IP address, nobody could connect to you, and BitWise wouldn't be very useful at all. You can't have it both ways: you can't have direct connects and not reveal your IP address. Does revealing your IP address constitute an insecurity? We do not believe so. See similar questions...

Most computers connected to the Internet are identified by a unique number called an IP address (for instance, 81.31.115.90). IP addresses do not correspond to a geographical location nor are they easy to remember. Also, IP addresses are FIXED (if you change web hosting companies you'll need to get a new IP address for your site). See similar questions...

In general, a static or dedicated IP address will only be available in conjunction with SSL. Please contact us at sales@cheaperwebhost.com with your needs. See similar questions...

There are four types of switches that you'll need to concern yourself with. When you're starting out, you can ignore all of them! The dual rate switches let you choose how sensitive the control sticks are. Typically, "high rates" are used for aerobatics, which require a faster tumbles or pirouettes, and "low rates" are used for hovering, where slower, softer responses will give more precise control and smoother performance. See similar questions...