Power input requirements of the welder are: 115V, 60Hz, 12 amps. Please follow chart on front of unit for proper extension cord size.

The K3 DC voltage required is 13.8 V nominal/recommended; 11 V recommended minimum; transmit disabled below 10 V; system shutdown below 9.0 V. The K3 is portable, thus it's designed for operation with a 12-V vehicle battery or gel-cell. Estimated minimum current draw with no enabled options is 0.9 A on receive, 3 A at 10-W and 20 A at 100-W. These figures will be refined after further testing. On all HF bands, TX with a 12.0-V supply still allows 100 W+ output.

We will need 2 14 amp circuits (110 volts), We will need 1 additional plus in for powering our lights for nighttime clients.

Whenever ACAOM proposes changes to its accreditation standards, it invites public comment at hearings and in writing. Providing oral or written comment is one important way to have input. ACAOM also welcomes unsolicited input from the practitioner community at any time, either directly from individual practitioners or from professional organizations.

The WOW Thing is packaged with a 110 AC/AC adapter and can be used in any country operating at 110V. The power adapter is fitted with a US wall plug.

The 3GEN Series is designed to provide maximum output power at nominal output voltages. We calculate the power output of a unit by using the nominal output voltage (not the set voltage) multiplied by the maximum continuous current you plan to draw. These should be summed for all modules: the total power should not exceed the maximum power of the input module selected.

Get a stereo 1/4" jack for the input of your pedal. Connect the tip connector to the input of the effect. Connect the sleeve to the ground of your effect. Connect the 3rd connector (the ring) to the negative of the battery (or the positive if your pedal uses a reversed power supply such as the Tycobrahe Octavia or some Fuzz Faces). When the cord is inserted into the jack, the ring connects to ground completing the circuit.

Tempest has developed a chart showing the power requirements of our electric blowers. It explains the generator, amperage, wattage, circuit breaker requirements and cord gauge as well as the maximum cord length for various models. It is available in the “Download Library” on the Tempest web site. This information is also available in the current Tempest product catalog.

On motorcycle lifts they are air operated. On PP-7 4 post 110 volt is needed. On 2 post lifts 220 volt is needed.

Standard 110 power outlet (power surge protected preferred) and a dedicated telephone line is highly recommended. The ATM only dials local or toll free numbers. No long distance charges.

The SONAbeam™ 155-M and 622-M both operate using 48VDC power and draw a maximum of 255 Watts. (Minimum recommended power supply capacity is 300 Watts and 6.0 amps.) The SONAbeam™ 155-S and 622-S run on 120/240VAC power and draw a maximum of 240 Watts. UPS or battery power is recommended in all cases.

The Magellan RoadMate can be used to provide off-road positioning information. You would simply press the "LOCATE" button on the front of your unit.

All of our bands require two 20-amp dedicated circuits with the exception of the Chuck Wansley Band, which requires three 20-amp dedicated circuits.

We ask our clients to provide a stage or floor space of 24x12x10 feet. For electrical power we require two standard 120V power sources within 20 feet of the band's setup location. Click here for stage plot.

To run all of the equipment, we need a dedicated 20 Amp circuit; and the power outlet should be as close to the DJ station as possible. I do have 100' of power cable. For remote sites I can provide a generator for all of my equipment. There is an extra fee for this service and arrangements should be made prior to the engagement.

Each product has a downloadable product information sheet which provides the equipment power requirements and other operating information. For any additional information contact our office at 1-800-683-0928.