Damp mop your flooring at least one time per week (more often for heavy traffic areas). Never use a detergent or soap, because it can dull the surface or promote the growth of mildew. Use protective mats – good quality entry and exit mats will help protect your ceramic tile from premature wear. They trap the dirt, sand, grit, and other substances such as oil, asphalt, or driveway sealer that would otherwise be tracked onto your floor.

Ans: Ceramic ball bearings are more preferred than metal ball bearings because of the following reasons: See similar questions...

Bearings are cylindrical mechanisms that go into the skateboard wheels. They have an inner central shaft which fits over the skateboard truck axles. They have an outer shaft that fits into the skateboard wheel. In between the two shafts are small steel or ceramic balls that roll in what is called a raceway. Bearings make world of difference in the way a skateboard rides. A lot of companies like to rate their bearings with the ABEC rating. See similar questions...

Yes. During negotiations for the new Apple contract, DET and Apple Computer Australia were not able to reach full agreement on some warranty-related clauses. Some Apple warranty conditions are therefore now closer to 'retail standard' than under the previous contract. The Department must therefore point out the following differences: Notebooks that are delivered in inoperable or damaged condition will now be assessed for "Dead on Arrival" status by Apple, rather than by the Department. See similar questions...

Rubber vibration mounts (sometimes called "silentblocks" or "sandwich mounts") should be inspected before every flight, and replaced if there is any sign of cracking or separating. Like belts, if you can't get replacements from your paramotor dealer, they can be purchased from industrial suppliers; however, I have found that the generic ones sold by McMaster-Carr (normally a good supplier) don't hold up. See similar questions...

Yes the thrust bearing races are close to the same size. The easiest way to tell which one has the larger inside diameter is to place them on the spindle shaft and rock them back and forth. The one that moves the most is the one that needs to go toward the center of the rotor. The other one with the smaller inside diameter goes toward the blade. See similar questions...

Your wheel bearings should be inspected and repacked with fresh grease on a regular basis. Due to the speeds attained by our smaller trailer wheels the grease around the bearing heats up quickly. Dexter Axle, the manufacturer of most pop up axles states in their service literature: "Along with bearing adjustment, proper lubrication is essential to the current function and reliability of your trailer axle. Bearings should be lubricated every 12 months or 12,000 miles. See similar questions...

If your bearings begin to feel gritty or notched to the touch, they should be replaced. When bearings sit idle for a long time, they must be protected from any moisture. If any moisture has gotten to the bearings, they will need to be replaced. Why does some new equipment come in with bad bearings? Often they are noisy or rough on first startup and often they fail in the first few hundred hours of operation. See similar questions...

Yes we can make it quiet. A good 2 into 1 exhaust with baffles will give a slight increase in performance. We just went for the sound.) flying. Zenith 601 XL, HD, Rans S6ES, Sonerai, Baby Ace, KR 2, Fly Baby, Powered Parachutes, Loehle 5151 and it looks like a 701 soon. Not all are flying yet.) to 4200 cruise. 5000 to 5200 max depends on gear ratio. The longest we have ran one at max power is 2 hours.) See similar questions...

Generally, Harley used a Timken style tapered roller bearing with a .750” I. D. on all wheels 1999 and older. These require manual grease packing, external oil seals, and generally more maintenance than a sealed ball bearing. In 2000, H-D changed to the sealed ball bearing, but maintained the same ¾” I. D. in most fronts. Many of the rears changed to the 1” sealed bearing as well. Some of the exceptions are; the FLH line and the V-Rod. See similar questions...

To absorb the disalignments of the shafts' supports, avoiding vibrations and efforts that have effect on the assembly's length. See similar questions...

It depends on the type and size of the greenroof. Most homeowners could check a flat or low pitch greenroof. A roofing professional should if it is too large or intensive – you can include a maintenance agreement of at least twice per year with the greenroof contractor/greenroof company. Or you can work out an arrangement with the roof maintenance staff of your building. See similar questions...

Initially, because I was losing track of all the events. Then, because when I get asked the same question(s) several times a day, by miscellaneous colleagues, friends, acquaintances and family members "what's wrong with you, anyway, you don't look sick.. See similar questions...

Some you can soap up, wear in the shower and rinse off. Some you can soap up and rise by hand in the bathtub (like a sleeping bag). Some you can use a bucket of warm soapy water, a scrub brush and a water hose in the back yard. This is basically for two reasons: 1.) Most outerwear garments have some sort of applied coating, which does not react well to many cleaning solvents used. They tend to weaken and ultimately destroy the function of the coating. 2. See similar questions...

Air bearings may appear to be an attractive alternative to the present bearing system of the CLD motors. However, reasonably sized air bearings do not have the lateral stiffness needed for CLD motors. See similar questions...

We've also got detailed bearing and spring replacement instructions on our 'Technical Information' page. Be sure to also check out our 'TransTrem Tips and Information' page to for setup pointers. See similar questions...

In the case of bad bearings, it is HIGHLY recommended that you send back either the headstock with spindle or the reg wheel housing together. See similar questions...

The magnetic field of the base pushes sideways on the electrons in the top as they spin through the field. In a metal top, which conducts electricity, the electrons would flow. Resistance in the metal would damp these 'eddy currents' and dissipate the top's rotational energy, causing it to slow down and eventually fall. The ceramic top is an insulator, so the eddy currents cannot flow. See similar questions...

Ans: Packages are pre measured for 1 Gal, 2 Gal and 5 Gallons of paint. Money saving bulk packaging is available also. You can figure on an average coverage rate of 250-300 sq. ft. per gallon for most house paints on smooth surfaces. See similar questions...