Valsir - F.A.Q. HDPE
UNI EN 1519-1 standards indicate 95°C, whereas the softening point, namely the temperature which causes the piece to deform corresponds to 125°C. Therefore, even temperature peaks exceeding 95°C do not create problems.
GMF-Gouda / Duprat Thermorotor: giving thermal treatment wit...
The Thermorotor is able to deal with relatively high pressures. On the process side, the pressures may run up to 20 bar(g) and on the medium side 6 bar(g). The standard model permits temperatures of up to approx. 200 °C. Variations are possible following consultation.
Frequently Asked Questions - FAQs - Hedwin Corporation
Since Polyethylene melts at 250 F, but softens at a much lower temperature, we recommend that the maximum fill temperature be 180-190 F.
PolySwitch Product FAQ - Tyco Electronics
For the operational state of most PolySwitch products the usable range extends up to 85°C ambient. For some product families (i.e. PolySwitch TD, Chip, AHR, and RHE devices) this can be as high as 125°C ambient and for others, such as the PolySwitch VTP device, it may be as low as 70°C ambient. In a non-operational state, some devices (i.e. PolySwitch SMD, miniSMD, TS) will withstand solder reflow temperatures for a short duration.
Raychem Circuit Protection - Polyswitch™ Resettable De...
This depends on the product family in question. For the operational state of most of our products the usable range extends up to 85°C ambient. For some product families (some TD, Chip, AHR, and RHE devices) this can be as high as 125°C ambient and for some others (VTP) this is as low as 70°C ambient. For a non-operational state some of our devices (SMD, miniSMD, TS) will withstand solder reflow temperatures for short duration.
Frequently Asked Questions: Service: Allison Transmission
Grade Braking is not intended to reduce the need for great care by the driver when driving a heavily loaded vehicle down a grade. Drivers should continue to take all normal and appropriate actions to keep the vehicle under control at all times.
Valsir - F.A.Q. HDPE
The UNI EN 1519-1 standard only refers to HDPE pipes and fittings for waste systems inside buildings, however the raw material is the same material used to manufacture pressurised HDPE to transport H2O.
Power Chips plc - Frequently Asked Questions
A - In our first generation, it will be on the order of 250C, as set by the curie points of the piezo elements regulating spacing. Because of the broad selection of materials available to us, operation will go well above 1000K. We have a known failure of 2 years’ operation at 1600K continuous, and 10 years at 1200K. This is why we position Power Chips as the ideal waste heat recovery technology -- getting more power from a given quantity of fuel.
New Page 1
High Density Poly Ethene but most commonly known as Polythene. One of the most common plastics you use in daily life it has an oily-type finish. Some of the original Prototype Stunt Stormtrooper Helmets were made in HDPE as Andrew Ainsworth (the original maker of the helmets) had some of this plastic in stock as he was making Garden ware and Fishponds. It was a khaki-coloured plastic and due to its oily nature it was a bit of a struggle getting the white paint to stick to it.
Kombucha FAQ Part 1b sugar - Frequently Asked Questions
The higher the temperature, the faster the fermentation process, and the faster the sugar will be used up and converted into acid.
Fluid Metering Frequently Asked Questions
PVDF pump heads have an operating temperature rating of 212 deg. F (100 C). However, these pump heads can be autoclaved (non-operating) at temperatures up to 240 deg F (116 C).
New Logic Research, Inc. -FAQ
The maximum temperature is determined by the membrane. Maximum temperatures range from about 60°C to 130°C (140°F to 266°F). High temperature VSEP systems can operate at 130°C with a Teflon membrane.
Pericom - Frequently Asked Questions (FAQs) - By Product Fam...
Maximum junction temperature can be calculated using the following formula: Tj = TA + P[QJA] ; Where TA = Ambient air temperature, P = Power(watt), and QJA = Theta JA What is the difference between operating free-air temperature, and operating ambient temperature? They both use the same symbol TA. Operating free-air temperature and ambient temperature are the same, with typical temperature at 25 degrees Celsius.
The maximum continuous operating temperature is 180oF and is capable of 212oF for intermittent use. Fusion LockTM seals are recommended for high temperature applications.
The maximum temperature for the spun bond polyester pleated bag is 200º F and the maximum temperature for the spun bond Nomex pleated bag is 365º F. Top
Norwesco Black Vertical Tanks
Polyethylene storage tanks have a maximum storage temperature of 120 degrees F. Contents with a temperature in excess of 120 degrees F-even for a short period of time-can weaken the tank's structural integrity and make it susceptible to deformation and failure.
Associated Spring Products
The maximum operating temperature of standard gas springs and manifold systems is 80°C/ 176°F. However, high temperature gas springs and manifold systems are available. Contact Hyson Products for more information.
Durateck - National Coating Technology
DuraTeck sheets can be exposed to 700 degrees F without changing color. Exposure to higher temperatures tends to darken the color. The degree of darkening will vary depending on temperature variations across the stainless steel.
Jennings Technology - Technotes - Vacuum Relays, Vacuum Capa...
The maximum temperature is based on MIL-C-23183 specifications. Most ceramic capacitors are rated for a maximum temperature of 125ºC and glass capacitors at 85ºC. A complete response to this question can be found in the Jennings TechNote C-1: "Vacuum Capacitor Characteristics "