Every 2-3 weeks; more often would make the measurement error larger than the expected increment over time; less often would leave too long a time delay for reassurance when growth is fine, or detection of abnormal growth if present.

The measurements may plot above the 90th centile but it is most important to do measurements serially and to see whether they follow the slope of the curve. If the woman's size precludes confident fundal height assessment, serial scanning should be considered.

It is measured from the side of the shoe and from the bottom of the heel tip to the top at the middle of the heel.(ie. Where you would put the centre of your weight on the heel).

This procedure requires that the measurer have a clinometer with a % slope scale. The measurer moves back to a point where the top of the tree is directly visible. For trees over 100 feet tall possessing broad crowns, this distance will usually be 150 feet or more. Using the clinometer, the spot on the trunk that is at eye level is identified and the distance from the eye to the level point on the trunk is measured with a tape or laser rangefinder.

The floor-to-floor height is the height of your stair. It reaches from the surface of the bottom floor to the surface of the top floor. It is NOT a floor-to-ceiling height. You may have plans that will help you calculate this amount, but it is advisable to measure once the floor s are installed --often homes are built slightly different than shown in the plans. You may be able to measure the distance through the open stairwell.

To get the standard height measurement of the opening, be sure to measure the height in several locations. Normal gates are 3/4" off the floor when installed and are built normally to the shortest dimension. Watch for irregularities in the flooring and be sure there is room above the opening for face mounted gates. Always measure the "finished" floor to the top of the track.

A lot depends on what is customary in your part of the world. Scientifically we use meters, peak to trough, but at the beach that is pretty meaningless because everyone else there is using different 'scale', and each area has it's own scale. [almost, but not quite entirely unlike feet]. It is usual to adhere to local custom, however as alt.

The manual says 150 cc's (volume). Marzocchi technical support told me 45-55 mm from the top of the threads inside the fork legs with the springs removed and the fork's outer legs fully compressed. I've had excellent success using the height method. The easiest method to measure the height is to use a straw (of course, don't use it ever again). Take the straw and draw a mark around the middle of it. Now, measure down from your line 45, 50, and 55 mm and make marks at each increment.

No. Most likely this type of system will need to be built into when it is manufactured. It will be difficult to make an add on kit.

Both the HP and HS (at the tall height) are designed to fit in a standard 8 foot ceiling (about 7 1/2 feet). The HS has a short ceiling setting at about 6 1/2 feet.

Early pedometers were mechanical and used a moving lever arm to count steps. Electronic pedometers now detect movement through a spring loaded, counter-balanced mechanism that records vertical acceleration at the hip. Pedometers measure the number of steps a person takes throughout the day.

Bryce looks about 5'7" to me or taller...may be the heels. either way shes adorable. i think its common to adjust actor/actresses hights to accomodate rolls About two years ago, I saw Jennifer on the beach (South Beach. I stood next to her briefly and walked behind her for a short distance and she wasn't taller than me...I am 5'4 (barely) and I weigh 116 pounds. Jenn has to weigh at about 130-135 pounds. She was thicker than me all over and of course a lot in the butt.

There are two prefered points to measure vehicle ride height. Both measurements should be taken on a level flat surface. One is at the center of the fender well to the ground.The other is at the bump stop to the axle housing or frame..

Good question. A patient may also have scoliosis or severe contractions that prevent a true height measurement. There are (at least) three methods that may be used to estimate height when actual measurement is not possible: knee height, forearm length and demi-span. This is caused by missing or improperly installed dDoc print preview engine. Please reinstall from the CD, or download from the web site. This error too is caused by missing or improperly installed dDoc print preview engine.

No!! We do not maintain a height and weight requirement. We do require that all potential members maintain the appropriate physique in order to participate in the required movements.

Measure the width and length or diameter of the table you'd like to cover. Measure from the table top down to where you'd like the tablecloth to drop. Add the drop twice, once for each side:

Die temperature is one of the most important process variables in die-casting. For zinc die-castings, the normal range is 3500 to 4500 F measured at the surface of the die just prior to injection. If the die temperature is too low, cold-shuts will be encouraged and the parts are likely to stick in the die and on the cores. If the temperature is too high, there will be an increased likelihood of soldering, burn-on and casting distortion.

Doesn't the doctor tell me when to have the surgery? Your doctor should be a guide only. He or she provides the proper glasses and assesses the extent of the cataract and any other eye problems. But he can not interpret how your vision is being affected on a day to day basis.

There are many intangible aspects associated with Mensheds Australia and with men's sheds in general. The following will give you some idea of the issues we address on a daily basis.

Parts per million or grains per gallon are the most common. One part per million (PPM) is just what it says: out of one million units, one unit. Grains, or grains per gallon (GPG) is a weight measurement taken from the Egyptians; one dry grain of wheat, or about 1/7000 of a pound. It takes 17.1 PPM to equal 1 GPG.