Spiral cut deck nails are galvanized (so they won't rust), and have a spiral cut into them, kind of like a screw- so, they won't pull out as easily as a common/box nail. I use these, sometimes, to hammer bracing into transition templates. They hammer in quick- but, hold tight in the wood, like a screw. Galvanized deck screws have a coarse thread (unlike drywall screws, that have a fine thread- so, they're almost as prone to pulling out as common nails, over time), and are also rustproof.

Stainless steel nails, screws or fasteners. You’ll get best results if you pre-drill holes and countersink a small head nail or screw. For complete instructions, go to installation instructions.

No. There are many different types of mounting surfaces into which your products could be attached, such as concrete, wood, drywall, plaster, aluminum and steel, etc. It's not feasible for manufacturers to include screws/fasteners that will work for all applications. Within the installation instructions we list the most appropriate fasteners for a timber install.

Answer: Yes. However, there are many different types of mounting surfaces into which your products could be attached, such as concrete, wood, drywall, plaster, steel, etc. It's not feasible to include screws/fasteners that will work for all applications, but the ones included should work fine.

Each Safeway stair is shipped with all bolts, screws and fasteners necessary for assembly. Each package also includes a detailed assembly manual and extra hardware in the event you misplace some.

Contact a licensed well driller. You can find a list of licensed well drillers in the yellow pages of the phone book.

We do pre-drill for wiring when it is requested; otherwise, it is done on site as the re-erection is being done.

Yes they can. Aphano hidden deck fasteners were designed to complement the structural integrity of composite deck materials. Composite decking is a high quality product and does not have the same limitations as wood. If wood decking is used then it needs to be properly sealed to prevent water penetration. This is done more easily with Aphano hidden deck fasteners because there are no penetrations on the top or sides of the deckboards.

We include all of the hardware. However, we don't include the fasteners as the type changes with your geographic location and the type of construction.

To find the approximate number of Invisagrip? Connectors needed for your deck use our Deck Estimator -- or take the following rule of thumb: Using a board width of 8 inch you will need about 90 Invisagrip? Connector for 100 square feet. In a bucket you have 250 Invisagrip? Connectors.

For wood (the ideal surface on which to install) or drywall over wood, you can use #8 screws long enough to penetrate the wood completely (we recommend at least 1/2" of wood). We also recommend Hex Washer Head screws, like that shown to the left, because they offer threads the full length of the screw. They also allow you to get an extra grip on the screw using a hex nut wrench, plus they have a built-in washer.

The new ACQ (Alkaline Copper Quaternary) treated lumber requires stainless steel nails or hot dipped fasteners with a G-185 rating (1.85ounces of zinc per square foot of metal or ASTM A-153-D), to resist the breakdown over time because of the new Acidic preservatives.

Virtually all deck fasteners can be used with our plastic lumber. We use stainless steel hardware in the manufacture of our outdoor furniture. Plastic lumber also holds nails and screws 40-50% better than wood. Predrilling is not necessary, but depending on the application might be preferred. Our lumber will expand or contract slightly depending upon variations in the temperature. To accommodate potential movement, adequate spacing should be provided between adjacent and abutting boards.

For 16 on center decks, use our handy 16" Calculator to find the right amount of Invisi-Fast Hidden Deck Fasteners for your project by clicking here.

The MT2000 has no predrilled holes for mounting the unit on a post or a wall. This unit is designed to stand on flat, level, hard surface .

Yes, you will have to contact your health plan for pre-authorization of MRgFUS treatment prior to scheduling your treatment session. You may also have to get preauthorization for the pre-screening diagnostic tests that are required to verify you are an appropriate candidate for MRgFUS. We suggest you work with your referring physician and/or staff at the MRgFUS provider site you have been referred to for treatment.

You will receive registration forms from your physician or midwife to be completed and submitted to California Pacific Medical Center prior to your eighth month of pregnancy.

All fresh, frozen, dried or canned fruits and vegetables are acceptable, as long as they do not have sugars or fats added. A diet with dried, frozen and canned fruits and vegetables can be just as nutritious as one with fresh fruits and vegetables.

You only need to replace any timber or woodwork that is damaged or rotten. If it is comparatively dry with a more or less even surface, it will be fine. The beauty of EPDM, is that you do not always have to strip of the old roof covering. If the roof decking is rotten or the felt is badly cracked and degraded, then you will have to lift up the old felt. If in reasonable level condition, then underlay can be laid over the existing felt and then the EPDM directly over the underlay.

We have a 100% money back guarantee. We appreciate that buying products online carry a general risk that the product you order won’t meet your expectations when it arrives. However, we are confident in our product and want to assure you that it will meet your expectations.