You should never place a new mattress upon an old sprung base. Although it may look in good condition, the internal springs will have worn in the same predominant sleeping areas as the previous old mattress. Which means the new mattress will sink and follow the contours of the worn areas. This will not only permanently damage the new mattress, but also give you an uncomfortable sleeping unit.

Most bedding retail stores will assist with the disposal of old bedding as a value-added store service. Ask about this type of service before you purchase!

The U.S. Consumer Product Safety Commission estimates that the new standard may eliminate up to 75 percent of the deaths and injuries that occur annually from mattress fires.

Yes, most definitely. Mattresses that are old will have much higher levels of dust mites and droppings, dead skin, fungal spores, bacteria and germs. Our process is extremely effective and will make them clean and fresh again.

Unlike other online mattress retailers, we'll remove your old mattress at no cost to you. Because of sanitation requirements we do have to reserve the right to refuse to take an old mattress that is heavily soiled. Unfortunately, we cannot take futons, sofa beds or bed frames.

Yes, the following settings should be set in the PDL for compatibility with RFM96: Link Rate=9600, Modulation=GMSK, DCE/DTE Baud Rate=9600. See Radio section of FAQ for instructions on how to program internal radios.

Yes, as long as the frame is still in good shape. We would not want you to put expensive lenses into a frame that will break in a few months!

The rule became effective on July 1, 2007 and applies to all mattress sets manufactured in the United States or imported into the United States on or after that date. The standard requires that each mattress set bear a permanent label stating that the mattress complies with the standard.

All new mattresses take a while to get used to. However your body will soon adjust. It is surprising how slight changes in sleeping surface can affect your sleep. A smell of newness may affect you for a few days; even a slight difference in height may disrupt your sleeping pattern. These teething troubles are present no matter what new mattress you buy, foam or sprung. They will fade over time.

First there are physical indicators: there are visible sags and "valleys", the bed creaks, coils can be felt/are visible and there are rip and tears in the mattress surface or seams. Then there are body symptoms: back, joint and muscle pain, not feeling refreshed following a night's sleep, feeling tired/drowsy throughout the day and poor concentration.

Be sure to check the label! All Englander mattresses are made of the finest quality, new materials. They are never reconditioned or recovered. Mattresses returned to retail stores by dissatisfied customers are sent back to the manufacturers. In many states it is illegal for mattresses to be resold by the retailer.

The International Sleep Products Association (ISPA) says a good bed will last 8 – 10 years with continuous use. This time frame should be used only as a guideline because there are factors other than age that suggest that your mattress set is worn out and should be replaced. The following are some of the signs that indicate it may be time for a new mattress set :

You should give your new mattress at least one week before calling your sales person. You have sixty days to make a possible reselection. A stain proof mattress cover must be used during this period. If yourmattress is soiled in any way we will not be able to accept it back.

This question is often asked by clients who spent the previous night on a hotel bed! The answer is yes ? but at a premium rate. Be assured that all mattresses are fitted with new mattress protectors before reuse.

Rotate it. A new sleep set will feel different from an old set. The important support that the back and the spine need is complemented by the layers of polyfoam, dacron, insulators, and sometimes even wool, silk, or cashmere. The layers of upholstery in old mattresses become compressed and flattened over the years. Upholstery layers in a new mattress have a certain amount of air in these materials, therefore a break in period is required.

this time, a user can base a new entry on an existing one by cutting the header from the older entry and including it on top of the new coordinate file. This new file becomes the input file to be uploaded into ADIT. The ADIT editor can then be used to modify the information in the file. You can deposit one representative structure following the instructions provided in the RCSB PDB data deposition services in either PDB or mmCIF format. Write to deposit@deposit.rcsb.