The temperature you pour the gel at will produce the bubbles you want. In other words, if you pour your heated gel at 200 deg. F, you will have lots of bubbles. If you pour your gel at 175 - 185 deg. F. you will have fewer bubbles. This is contrary to what you may have heard and still may depend on how close you are pouring your gel. Pouring slowly at 185 Deg. F from close to the top of your glassware will limit the bubbles. Pouring at 200 Deg.

A fungus is a living organism that thrives in dark, damp environments. Fungal infections are very common in nails on both fingers and toes, but toenails are more likely to be affected by the fungus since it is attracted to dark and damp environments more typical of the foot than the hand. Affected nails have a yellowish or brownish discoloration and may thicken or become brittle over time.

A few bubbles may be of no consequence. One needs to practice to improve technique. Mixing and drawing require training and practice.

Involves registry editing. Navigate to "HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced", create DWORD value called EnableBalloonTips with Hex value of 0 and restart your computer.

If your nails become too long before your next appointment, you can file them using a 100 grit file or larger. NEVER use nail clippers as they may cause your nail enhancements to shatter. Changing the polish is fine, however, you need to use non-acetone polish remover. Cuticle oil applied daily helps prevent your enhancements from becoming brittle. Call your nail technician with any questions or concerns.

Nail technicians are required to keep their license visibly posted at their work station. Most states require that there be a photo of the license holder on the license. If you do not see a license, including a salon license, ask to see it. If this request is refused, leave the salon and report it to the local regulatory authority. Unlicensed practice is illegal.

The most common shape worn today is referred to as a "square" look. This shape has no rounding of the corners and appears to be a "square" looking nail. This shape is the strongest of all shapes, in that you have more product spanning the width of your nail tip, and less chance of breakage.

The wonderful benefit of nail enhancements is that you can wear nail polish with no polish chipping or peeling that often occurs on natural nails. However, the more you change polish color, the more apt you are to have "softening" of the nail product. When removing polish, you are using an acetone based polish remover. The acetone in the polish remover is the product we use most often to remove the nail enhancements from your natural nail.

Tanning with nail enhancements should not cause discoloration of the nail product, as long as your nail technician/manicurist is using a high quality nail product and applying a "UV" protectant top coat. However, if your nail should become discolored or "yellow" after tanning (some tanning lotions may cause yellowing), simply remove the top coat off of your nails.

If you wish to fix a nail on a Facing mounted on frames, make a hole using a drill a bit thinner than the nail, and then fix it - for, if you did it in the traditional way, unless the frame and the facing are perfectly fitted, you would be hitting an empty space. If you wish to nail a or sheet that is directly fixed on the wall, make a hole using a drill a bit thicker than the nail, and then place screws with plastic plugs. You cannot use thumbtacks on Corlok due to the hardness of its surface.

Yes, unfortunately ingrown nails can return. There are many reasons, including but not limited to: Injury or trauma to the area, toenail has been clipped too short, or shoes are too tight in the toe box.

Areas behind the paper where air is trapped and/or the adhesive has dried out without sticking the paper to the surface.

Ha! I say, "Ah Ha" because this may be the most important "secret" to manipulating these spherical beauties. Bubbles pop when something dry touches them (the dry object absorbs water and makes a hole). But something wet (soapy wet is even better) can touch the wall of a bubble without creating a hole. Using a wet straw you can blow bubbles into, onto and around another bubble. Start with a good solution and then practice, practice, practice. Good luck. (Did I mention practicing?)

Well, since you ask, I'm hoping to have a book out soon (if not already). Check here for my book info. For a list of other titles go here.

The LS finishes are almost bubble free. The same design which makes them flow and penetrate so fluently, acts as a built in de-bubblier. Diligent usage of heat will only cause more bubbles. Sometimes a very mild soft heat can be used after the resin has been mixed for about 20 minutes

Bubbles in a freshly applied finish, especially polyurethane, spar varnish or other thick finishes, are usually caused by 2 things, shaking the can instead of stirring it, and/or using a foam brush instead of a high quality bristle brush or cloth.

EMON is installed automatically provided that installation of MS Outlook 97/2000 in corporate mode is detected. MS Outlook 2002 (XP) and 2003 will be supported in the upcoming version of EMON, currently available as beta.

The menu bar is designed to adjust itself to the center of the page. But incase this does not happen, simply hit the refresh button each time you change the size of your browser window or change the resolution of your screen.

If you start a Sun Management Center console from Windows and the login window does not appear on your desktop, check the Taskbar at the bottom of you desktop for the Management Center task. Use this button to access the login window by maximizing it and resizing it accordingly.