The dirt streaks that are being created above your baseboard are mainly dust, dirt, and carbon soot that might come from fireplaces, water heaters, furnaces, standing pilot lights, candles, cigarette smoke, cooking byproducts, and even automobile exhaust by the natural convection that occurs during the heating cycle.

This is largely a design choice. If your heaters are standard height, we recommend that you order your wainscot with a base height 1-3" above the heaters. If they are tall, like older ones that are sometimes 24" tall, we recommend that you just ignore them for ordering purposes. During installation, you will just cut around them. See similar questions...

Yes. You can now find programmable AND more accurate thermostats made especially for baseboard heaters as most home improvement or hardware stores. But before you go, find out if your baseboard thermostats are single-pole (two-wires coming in from the wall) or double-pole (four wires coming in from the wall). Most are single-pole and not always interchangeable. (A double-pole thermostat will have an "Off" setting. See similar questions...

Here is one way of doing it, a picture ready is worth a thousand words. If you have allot of baseboards to work with we suggest that you order a few extra lower rails (PW-8) and the router bit to customize the stiles on site easily. See similar questions...

No, dirt streaks are almost always caused by poor design. All air has dirt in it. If the speed (velocity) of the air exiting your register is higher than it should be the dirt is actually impacted on the wall or ceiling surface. A solution is to add another register from the same duct serving this register; this reduces the speed of the air by distributing it to two registers instead of one. It will also reduce the air noise coming from the original register. See similar questions...

In most instances, this is caused when the film leader is pulled crookedly or at an angle causing the positive to separate from the negative immediately after the film exits the camera. Otherwise, the film may have curled while in storage if the pack was stored in heat/humidity. The difference between a passport camera and a photo id camera is the size and number of photos that are printed per sheet of instant film. See similar questions...

Oil heating systems rarely cause those dirty streaks and smudges that can appear on the walls, ceiling and other areas in your home. Things that do cause this include: See similar questions...

Scratch marks are a typical occurrence when using a heat shoe laminator. Scratches occur when the lamination film passes over the hard heat shoe surface. In order to completely eliminate this, a heated roller type laminator should be used. In lieu of purchasing a new machine, you can try cleaning the heat shoes with a roll laminator cleaning kit or roll laminator cleaning block. Dirty shoes may cause film scratching as well. See similar questions...

Yes you can. All you need to do is provide a Radiantec mixing valve to step down the temperature of the water to the radiant circuits. You mix hot water from the boiler with return water from the floor to provide a lower temperature. See similar questions...

Pure ceramic. There is a hair-thin wire filament running through it. Our Pure ceramic heaters are made specifically for SaunaRay. They have a concave shape which allows the edges to fan-out the waves and the heat to cover a larger area. The Stainless steel reflectors are mirrored and made out of 100% surgical grade stainless steel. They reflect the far infrared heat even wider, ensuring a complete 360 degree coverage inside. You are surrounded by far infrared heat! See similar questions...

The factory installed propane furnace does a pretty good job of keeping the pop-up warm, but you WILL go through a lot of gas. A normal 3 day weekend with evening temperatures in the 30's or 40's will use a full 20 lb tank of LP gas. If you're camping on an electrical site some people suggest taking along a small electric heater as well ... it will allow you to cycle the furnace off a little more and thereby us less gas. See similar questions...

Unsightly black stains on shingles are often mistaken for fungus, mildew, dirt or oil, but are actually caused by a hardy type of algae. This common problem has increased during the past 20 years, indiscriminately settling on rooftops from coast to coast. Dark algae streaks are visible when algae cover the normally vibrant colors of white, cobalt blue or hunter green roofing granules. See similar questions...

Streaking can be caused by a number of things. The most common thing is, have you used wax or polish on the vehicle? The build up of these products can cause a thicker layer to form on the vehicle allowing the black streaks to eat into it. Once the cleaner starts to cut through the layers streaks can form. The streaks are the clean bits and the use of a 10:1 solution of cleaner will help speed up the cleaning process. See similar questions...

There are tools designed especially for this purpose. The Super Guide by Hyde? Tools is a metal shield that can be placed between the carpet and the baseboard allowing you to paint one section at a time. Another method is taping the carpet with masking tape or masking paper. See similar questions...

No, the system generates low temperature heated product that works well with radiant floor heating systems, warm air heating, Solar Domestic Hot Water (SDHW) heating systems and other types of low temperature heat distribution systems. See similar questions...

Chances are, you used too much Z-6. Z-6 is SUPER CONCENTRATED and you should be able to wipe down an average size car with less than one ounce!! Apply Z-6 sparingly, and work in small sections, rubbing the Z-6 until it dries and gets slick.Also, turn your towel often to be sure that you are See similar questions...

A piezoelectric switch (pronounced peezo) contains a crystal that exhibits piezoelectric properties. A piezoelectric crystal converts mechanical force into an electrical voltage, hence, you press the button and an electrical charge is used for ignition. If you have ever started a gas barbeque you have used a piezoelectric switch. Continuous electronic ignition is a constant spark generated from an electrical source. It keeps sparking as long as the heater is on. See similar questions...

Most FIR sauna heater elements are steel-coated. Steel coating is an older technology that directs the heat source but requires more time to warm up, operates at higher temperatures, and uses more energy to reach the level necessary for deep tissue penetration. Now, ceramic-coated heater elements result in lower temperatures and more efficient energy use. Ceramic-coated FIR heaters produce the same useful energy as the sun at a very safe (. See similar questions...