The Monoblock LNB (for Astra 19.2 degrees east and Eutelsat Hot Bird at 13 degrees east) has the degree separation already pre-built. The Eutelsat feed should be the prime focus aligned LNB (as per the diagram). Our Monoblock LNBs have DiSEqC (automatic LNB switching) in-built, therefore no additional DiSEqC switching equipment is required.

Typically, LNBs are bolted to the feedhorn. You would need to unbolt the old LNB and connect the new one using your old bolts or ones that are provided. It is a good idea to use coax cable seal after you install the new LNB. On an older system the new LNB may not fit on your feedhorn. Older LNBs were larger and to fit them under the feedhorn cover a 90 degree elbow was installed to lay the LNB flat. If you remove this 90 degree elbow your new LNB will bolt directly to the feedhorn. See similar questions...

LNB stands for Low Noise Block downconverter. An LNB detects the signal relayed from the feed, converts it to an electrical current, amplifies it and lowers its frequency. The downconverted signal is relayed via coax cable to an indoor satellite receiver or DVB card. You have analogue LNBs with a frequencies range from 10.950 to 11.700 GHz and Universal (digital) LNBs, which cover our frequency, range up to 12.75 GHz. See similar questions...

A Dual LNB is just two LNB's...each connection can operate independently of each other so you can have two receivers each looking at different stations on different transponders. They both look at the same satellite (101 Degree satellite). A single LNB only has one coax connection and cannot be used with more than 1 DirectTV receiver. See similar questions...

You can check whether your LNB is digital or not by looking at the frequency range, which is usually written on the LNB. When your LNB is digital this frequency range goes up to 12.75 GHz. If it is analogue this frequency range only goes up to 11.75 GHz. See similar questions...

The DSR is the Digital Satellite Receiver. It receives the digital signal from the dish and processes it into a video signal. The LNB is the Low Noise Block converter. It converts the incoming satellite wave to electrical signals. See similar questions...

With each new install of the client, you are given a new node ID. Each time you re-install the client, you will have another node ID. When you reinstall - just copy that file to the same directory it was before and you will not have to add another node to your stats. No. If you stop a run before you have completed all the conformers for a candidate, the docking will be aborted. See similar questions...

Unfortunately it is not possible to receive our service with an analogue LNB, since an analogue LNB cannot receive the frequencies on which our service transmits. Europe Online operates from digital satellite signal and requires that the home satellite dish be equiped with a digital LNB, called Universal LNB. See similar questions...

No twin-output LNBs are manufactured for an oval Sky minidish. (I've seen some advertised on eBay but these are actually designed for a circular dish so bad-weather performance is likely to be compromised). There is a quad-output LNB kit available specifically for the Sky minidish. This includes an adaptor that will let you fit the LNB to any of the three main makes of minidish. See similar questions...

The Wegener QPSK digital video products have been designed to be functional with low cost NON PHASE LOCKED LNB's. See similar questions...

How do I program in the KU satellites with my older receiver? The names are different and it won't take the new names. See similar questions...

For use on your company's intranet, installation on your network server merely requires a simple installation. You may also choose to access the program through the internet. See similar questions...

Installing MediaWiki takes between 10 and 30 minutes, and involves uploading/copying files, and running the installer script to configure the software. See similar questions...

See Manual:Extensions for information about installing extensions, as well as writing them. See the Extension Matrix and the to find existing extensions. See similar questions...