There are several program to do this. They actually work with WAV files, not MP3, so if you have problem MP3 files, you'll have to decode them to WAV files, fix the WAV files and then re-encode (unfortunate... but because of the way MP3 compression works, trying to do any editing directly on MP3 files is very tricky). The program names that I am aware of are: You can download all of them through the ZDNet software library at www.hotfiles.com - just search for the names.

Peel the outer vinyl layer off dry. Soak the backing layer, wait 10 to 15 minutes and scrape off. For more detailed instructions or options, see our wallcovering removal guide.

You can revive your Brillante with Simichrome, a wonderful non-abrasive polish available through your Brillante dealer, but if it has been deeply scratched, there is no way to thoroughly buff out these marks. We recommend storing your Brillante in its flannel pouch for optimal care.

Over time the cooking surface will become "worn" and get tiny scratches from regular use. Many people like that and refer to it as "patina". Should it get to much for your taste, just have the surface "buffed up" by a professional.

Well, connecting the output from a magnetic phono cartridge directly into a sound card probably is not going to work very well. The output from a magnetic cartridge is very low level. Not only that, but it also has some inherent frequency distortions, which the pre-amp circuits in your stereo are designed to correct for. So..

You can only remove stores that you added. Any other store you would like removed should be marked closed, sold, or other (with an explanation) for the status, and it will be removed from your file for the following year.

Dents are depressions in the wood where the grain is not broken. Scratches and gouges are areas where the grain has been damaged. After the finish is removed, most dents can be steamed out. Fold a piece of paper towel, wet it with cold water, and hold it on the dent. Place a hot iron on the dent for a few seconds until steam is forced into the wood. The dent should rise after a few applications. Sometimes a small amount of sanding is required. Always experiment in an inconspicuous area first.

First, make sure you use a good stainless steel cleaner. Once you're done cleaning, follow up with good stainless steel polish. Cleaning will only blend in light scratches; deep scratches may require more work or sink replacement. Use Bar Keepers Friend cleanser and a green Scotch-Brite pad. Wet the sink and pad, and sprinkle a little cleanser in the sink. Gently move the pad front to back on the bottom to blend the scratches in. On the sides, scrub in a circular motion. Rinse thoroughly.

To install FLOWCOM 32, simply put Disk 1 into the computer and run "SETUP.EXE". The installation wizard will then guide you through the installation process. For any other questions, please refer to section two of the SPIDR manual. Please note that FLOWCOM 32 can not be run from floppy disks and must be correctly installed on your hard drive.

Send $10.00, payable to Jack Hardy, to Great Divide Records at the address on the Contact Information page. (Some of the songs on this album are on the first CD, Early and Rare, of The Collected Works of Jack Hardy, vol. 1.)

With some stereo recordings, it is possible to remove the vocals because of the way in which the recording was mixed at the studio. Often, the vocals are placed in the exact center of the recording, while all other instruments are slightly off-center. If you subtract the right channel from the left channel, the vocals get completely canceled out, leaving only the other instruments.

It is always best to turn off cell phones and pagers before the concert begins. Noises such as pagers going off or a cell phone ringing are very distracting to the conductor, the musicians and your fellow audience members, and are considered to be quite rude.

If required to remove the software, please proceed to Start | Programs | iNetBet and select the "Uninstall iNetBet" option. This will completely remove the iNetBet software from your computer.

There are some vinyl album purists who enjoy the audible pops and clicks. For many others the pops and clicks are somewhat distracting. There are numerous pops and clicks on each vinyl recording. When we restore a record we have to decide how severe the pops and clicks are, and how much correction to apply to the music with our software (see Trade-offs)

Disk Groups help you organize Dynamic Disks and help to prevent data loss. Windows 2000 allows only one Disk Group per computer (this may change). Disk Groups can organize storage when you use Veritas LDM-Pro. A Disk Group uses a name consisting of the computer name plus a suffix of Dg0. If you use LDM-Pro, the suffix can be incremental, such as Dg1 or Dg2. To view the name of your disk group, see the following registry entry:

There are a number of possible causes for this, especially when using a Windows-based PC. We suggest you take a look for suggestions in our extensive Audio Interface Troubleshooting Guide (.pdf, 105 KB).

All our PC/Mac CD-Roms provide loops that are compatible with any audio sequencer that will accept 16-bit, 44.1khz audio files - including Sonar, Guitar Tracks, Home Studio, Logic Audio, Cubase SX and Digital Performer. Check here to work out which format you need - or ask us if you need any help.

To record data you can use Roxio Digital Media LE version 7 which is bundled with the drive or upgrade your current recording software to the latest version as soon as they add Blu-ray support. If you intend to author, record and playback high definition (HD) video using the Blu-ray recorder you will need a professional software package like Sonic Scenarist. Lower cost, consumer, Blu-ray authoring packages will become

Absolutely not, our product is stand alone, which means no purchases of additional tools or added headaches. After your purchase you'll have access to one of the best Burning tools out there today for FREE.