Solution: Gradually close the air control mechanism in order to keep the flue temperature within the comfort zone, between 250 and 475oF (150 to 250oC). If you do not have a chimney thermometer and would like to get one, visit your local Osburn dealer. Solution: Replace the gasket using a genuine OSBURN adhesive and gasket kit. Please consult our accessories sections. Solution: Put less wood into the fireplace. The fireplace will not produce as much heat and will not heat as long.

AXTRO® is capable of heating areas above 260 square meters (buildings constructed to regulation 10/91) with any number or type of radiator installed.

Solution: Use smaller pieces of wood and place them to allow proper air circulation between the logs. The same weight of wood cut in many small pieces will produce more heat than fewer, larger logs. Only add big logs when you have a good bed of red embers. Logs with a diameter exceeding 6 inches (153 mm) should always be split. Avoid stacking logs to the top of the fireplace. Solution #1: In many cases, a weak draft is simply due to insufficient heat in the exhaust system.

InFlame Fireplaces have a heat output of up to 9000BTUs/hr depending on the fireplace. This is guaranteed to bring ample warmth to any room in your home. A typical electric fireplace offers from 1500 to 5000 BTUs/hr (approximately.) so our entry level 6000 BTU/hr max. output fireplace will provide you with a great heat supplement.

A one-cone difference is common from top to bottom of an unvented kiln. You can observe this difference with cone groups set at different levels. The difference can grow great with larger electric kilns, especially when firing to low temperatures. For example, cone 03 has bent on a top shelf when only cone 05 has bent on a bottom shelf. Tests have shown a 30° difference top to bottom on high fires and 80° difference when low firing.

There are a few precautions to take before implementing this TV application. First, take a thermometer and tape it to the wall above the mantel (where the plasma TV will be placed). Then and build a fire, let it roar while. Check the thermometer. If the temperature is above 90 degrees then the area is receiving too much heat - either escaping from the front of the fireplace and rising up the face, or radiating through the chimney to warm the outside wall.

Many factors may include: Down drafting, inadequate chimney height, incorrect or missing raincap, lack of free area around raincap (i.e. trees too close, roof structure, other vent systems), damper problems, improper installation, etc., etc. It may be one or a combination of any of these factors.

Lamartine has a lead in time of 3/4weeks from the moment you confirm an order to the time of installation. Should you wish to have your fireplace installed sooner than this, it can be possible for us to schedule a shorter time, however please note that this cannot be confirmed until a site survey takes place.

All vent-free appliances, whether natural or propane, produce water. The accumulation can range from 3/4 to 1pint of moisture per hour in the room. Under normal conditions, this does not cause a problem. However, if you have a problem, you will need to provide an outlet for this moisture. This can be accomplished by providing adequate ventilation or using a dehumidifier to help control the moisture.

Solution: Make sure you use good, seasoned wood. The wood you burn plays an important role in the overall performance of your fireplace. Your wood should have been properly dried for approximately one year. Another key is storage. Wood that has been cut for one, two or even more years, will not necessarily be dry if it has been stored in poor conditions. Under extreme conditions, it may have rotten instead of drying. Smaller pieces of wood will dry faster.

The heat from the earth's core continuously flows outward. It transfers (conducts) to the surrounding layer of rock, the mantle. When temperatures and pressures become high enough, some mantle rock melts, becoming magma. Then, because it is lighter (less dense) than the surrounding rock, the magma rises (convects), moving slowly up toward the earth's crust, carrying the heat from below. Sometimes the hot magma reaches all the way to the surface, where we know it as lava.

This can vary from one dog to the next. Typically, the heat cycle lasts around two to three weeks. The female's vulva will swell and then bleed for several days. Mating is typically done after being in heat for a good 10 days. Some females have what is called a silent heat. This occurs when a dog does not show the typical signs of being in heat but can still get pregnant. Be careful if your dog is in heat and you do not wish her to be bred.

Heat naturally rises therefore the bottom of the kiln can fire cooler than the top, especially at lower temperature ranges. On tests conducted on a 10 cu. ft. kiln with pyrometers at six levels, it was found that the EnviroVent can cut temperature differences to about half of normal. The top-to-bottom differential was cut from 79° to 45°. Some users have reported even greater improvement in heat distribution.

Yes. Aside from the fact that all of our fireplaces radiate heat from their fronts, there is still heat that can be withdrawn from the fireplace. Using the blower increases the airflow thereby maximizing the heat being conducted from the back side of the fireplace. Adding a fan is easily done if 110 power is hooked up to the electrical box inside the unit. If power is not already at the fireplace, it still may be possible but may be more costly.

More so. A Bellfires? will provide ample heat without the grills and fans. The special refractory material of the Rosin Design radiates a comfortable warmth into the room. This type of system has been used in Europe for over 65 years.

The product can not be installed in any area where its temperature could exceed 120?F. Solid wood moldings or trim may be used to buffer the product in these areas.

Conduction is the process that occurs in substances denser than air like water and wood and stone where the heat moves through the substance. Conduction occurs rapidly in metals like gold and copper and very slowly in an insulation like fiberglass. Convection is the process where air makes contact with substances that are conducting heat and the air is heated.

Blaze King gas appliances are unique to the industry in that most Blaze King gas models have heavy-duty heat exchangers. Superior engineering and design has allowed Blaze King to fit the maximum amount of square inches of surface area of heat absorbing steel into each model. The more surface area of steel, the more energy absorbed during the combustion process. Then, the variable speeds fans that are standard in all gas models then moves that heat into your home.

Canine heat cycle occurs 2 times a year,and lasts for 3-4 weeks. They bleed for a week, cease for a week during their fertile period, then bleed for the last week. If you think your dog is pregnant, gestation is 63 days from time of breeding.

CaesarStone is structurally more heat resistant in comparison to other stones, including granite. However, any stone material can potentially be damaged by sudden and rapid temperature changes, especially near the edges. Therefore, using inexpensive and readily available hot pads or trivets is always recommended, especially when using cooking units such as electric frying pans, crock pots, or roaster ovens.