X-5 X-treme, V-600, V-600CS, V-400E, V-300, V-300CS, V-300-7 and All Fold-A-Vent Products can be used with any roof pitch from 3/12 to 16/12. For hip applications minimum over all roof pitch must be at least a 4/12 pitch. (The old style V-400 can only be used with up to a 10/12 pitch roof.) See similar questions...

The roof pitch is the slope of your roof. You can determine yours with a level and tape measure. Click Here for more info See similar questions...

The roof pitch refers to the angle or the steepness of your roof. Builders can use a carpenter's square to find the angle of a roof. See similar questions...

Sooner or later, every roof needs to be replaced, usually due to the long-term effects of weathering. If a residential roof is more than 20 years old, it is a prime candidate for reroofing. To determine if you need a new roof: On the ground, walk around your home with binoculars and inspect your roof for cracked, curled or missing shingles, as well as any excessive loss of the protective mineral granules. DO NOT CLIMB ON THE ROOF; walking on the roof is dangerous and can damage your roof. See similar questions...

Yes. We offer a 35mm modular low pitch conservatory roof system, which comes as an installation ready kit. Known as 'L2 in a Pack', this system offers sculptured cappings as well as the option of opal, bronze or 'Silhouette' polycarbonate. See similar questions...

The most accurate method for measuring your roof pitch is with a pitch gauge placed on the roof itself. This gives an accurate degree measurement of your roof slope. (A pitch gauge can be purchased at local building supply stores.) The alternative is to measure the rise of your roof divided by the run of your roof. See similar questions...

In northern Europe ideally, between 30 and 50 degrees; however, the system will work quite effectively from flat to vertical. For any other parts of the world please contact us for advice. We would always encourage you to check with the appropriate local regulatory bodies before purchasing a system. Local Authorities are charged with the responsibility of trying to reduce energy consumption in homes and are normally very receptive to innovative energy saving products such as SUNWARM. See similar questions...

If you do not see a question you may have listed here, please email Support at support@hartshearth.com or call us at 800-924-0850 and ask us. We are more than happy to answer all questions. See similar questions...

Garages - 10 or 12 degree roof pitch or we can accommodate a 22.5-degree roof pitch to match the roofline of the majority of older style Australian homes. Raised Barns - 10-degree roof fall on the sides and a 20-degree roof pitch in the centre raised section. See similar questions...

Grace recommends that the Grace Ice & Water Shield is extended a min. of 24"" beyond the inside face of the exterior wall line of a building and should extend from the eave above the highest expected ice damn. Check local codes and regulations as they may vary. If installing full coverage of Grace Ice & Water Shield, use same roof area calculation for finished roof covering. See similar questions...

We have design and reengineering resources to produce very complicated roof designs that can include high roof slopes as well as various roof configurations within the same project. See similar questions...

Amazingly, quite low: as little as 1/2:12 (1/2" to the foot) for standing seam metal roofs - a definite benefit for many low-pitch applications. Most other roofing systems require minimum pitches of 3:12. See similar questions...

A 4:12 pitch is standard on all Uni-Frame® and Town & Country buildings. Any pitch can be accomodated, however. See similar questions...

Answer: The best review a schematic of the bracing required, view the following documents from WTCA's Truss Technology in Building Series: Web Member Permanent Bracing: Brace it for Stability, Always Diagonally Brace for Safety and WTCA's Job Site Warning Poster. Answer: To answer this question directly, continuous lateral bracing is VERY important. Certain truss members require this bracing in order to carry the full design load. See similar questions...

Each of our flashing kits are engineered with specific pitch requirements. The roof pitch is important because it ensures that the roof has the proper slope to effectively drain water off of both the flashing and the skylight. The roof pitch and the roofing material used are both important in determining the type of flashing needed. See similar questions...