I have had a few emails on this one, and it seems to be a common error code on some Zanussi models. This error code seems to be the control board detecting a wrong configuration (in other words, an illogical set of sensing conditions, from its connected sensors and wiring).

Thanks to MT of Gateshead for this one. This particular code is used when the machine detects a pump problem or water draining problem (failure to properly pump all the water off in the designated time). In this case, the fault would occurr just before attempting to spin. It turned out to be a blocked filter, accessible from the bottom front of the machine. See similar questions...

See /waffle/docs/network.doc , 'Managing UUCP and USENET', or Ian Taylor's UUCP Internals FAQ, posted to news.answers, for details. See similar questions...

Error code 800 means - 'Unable to establish the VPN connection. The VPN server may be un-reachable, or security parameters may not be configured properly for this connection'. To solve this make sure that the in the UWS-VPN properties you have the VPN Server address as specified in the registration mail. For students this will generally be student-vpn.swan.ac.uk . An IP address should not be used. See similar questions...

This error means that your wireless device is nor enabled, connected to nomadic or sending/receiving as it should. Make sure that the card is switched on. Some laptops have a physical switch on the laptop to turn the device on. Also, go to 'Network Connections' and make sure that the wireless connection is enabled. If you are using software provided by your cards manufacturer to configure your wireless adapter, make sure it is configured to use the SSID of nomadic. See similar questions...

Below is a list of the main error messages you will see while searching the Wayback Machine. If you see an error message that does not have the Internet Archive Wayback Machine logo in the upper left corner, you are most likely looking at an archived page or the live web. Failed Connection: The server that the particular piece of information lives on is down. Generally these clear up within two weeks. Robots.txt Query Exclusion: A robots. See similar questions...

This error happens due to a bug in librsync that prevents it from handling files greater than 4 GB in some situations, such as when transferring between a 32-bit host and a 64-bit host. A patch is available from the librsync project page on Sourceforge. The CVS version of librsync also contains the patch. More information is also available in Debian bug report #355178. See similar questions...

That error message means that the time setting is incorrect, by at least 12 hours, on the computer on which the client or server is running. You should check and reset the system clock. We believe no security risks could be introduced, because handle servers provide a limited handle lookup and administration service that is constrained to the handle database. There have been no vulnerabilities found or security-related bugs reported in the software in over 8 years. See similar questions...

The Omron Instant Ear Thermometer will display this indicator after the On-Measure Button is pushed if the thermometer's own temperature is too cold or too hot to operate. The operating range is 50 to 104 degrees Fahrenheit. Put the thermometer in a room within the operating range. Wait 30 minutes and take the measurement again. See similar questions...

See the Error and Warning Messages section for help with specific error messages. Return to this section if you do not find a specific answer for the error message that you have. Search the Cygwin/X mailing list archives to see if the error message has already been reported and/or addressed. Report the error message to the Cygwin/X mailing list, how the error message was caused, and the behavior of the X Server after the error message was generated (exit, freeze, etc. See similar questions...

This means that your handle server is not responding to client requests. Make sure your handle server is running. If it is running, then check that ports 2641 and 8000 in your firewall are open to ALL incoming or outgoing requests, and make sure that the IP address in the prefix record is correct. See similar questions...

The error messages in Outlook are somehow very cryptic and do not go straight to the point. Error messages starting with "0x...." are more helpful to technicians with Microsoft than most people. Rather take a look at the message after the error code. It might give you a hint what is wrong, e.g. what mail server you have problems connecting to, is SSL on or off etc. See similar questions...

Contact your software vendor to request that descriptions be added to these error codes. A list of error codes can also be found on page 38 of your Dental Office User Guide. In the event that dental office staff cannot correct an error message, the problem should be referred back to the networks, as they are the ones sending the message back on behalf of the insurance company. The networks can pull up the claim (using the CDAnet office number) and find out why the error was sent. See similar questions...

When you receive any sort of transmission error or have problems connecting, call your software vendor to have them check your dial-up numbers programmed in the modem. If necessary, have those numbers changed. On occasion, the networks go through a migration schedule which de-activates certain phone numbers, which then need to be replaced with new ones. Dental office staff should discuss this with the vendor. See similar questions...

Note: Refer to the Technical Manual (also included in the distribution) for general information on server installation, using the GUI handle administration tools, using the HTTP Proxy, other tools and features, batch operation, advanced server configuration, replication, splitting a handle server, and using a SQL database for storage. See similar questions...

This message can be produced by any application linked to the WFDB library that attempts to read annotation files. In order to do so successfully, these applications need to find the annotation file for the annotator and input record you specify. The message indicates that the annotation file was not found in any of the expected places, or that it was unreadable. There are several common reasons why this can happen: The record name supplied to the application is not correct. See similar questions...

This error message means that a Cyclic Redudancy Check failed during some operation, most likely while gzip'ing or un-gzip'ing a file. Possible causes of this error include an incomplete gzip operation, and hardware failure. A brute-force way to recover from this error is to remove the rdiff-backup-data directory. However, this will remove all of your past increments. A better approach may be to delete the particular file that is causing the problem. A command like: will find the failing file. See similar questions...