I had to do this for a coulple of dozen boards.. Found the best way was to get a 'tile scriber' which is just a knife sized handle with a tungsten carbide point stuck on. You just clamp the board with a metal edge on it & scrape away heavily a few times, then snap on the scoreline. OK it's trivial & obvious maybe, but I tried to cut them in a bandsaw, DONT even think about it, also fibreglass powder is BAD for your lungs.

Fiberglass is a cloth made out of thin glass threads. It is used to reinforce plastics and other materials. FIBERLAND uses fiberglass to manufacture all our plastic products. Therefore the correct name for the material we use is FRP (Fiberglass Reinforced Plastic), although our products are said to be made of fiberglass. See similar questions...

AudioFormz enclosures are extremely well made and are made of 100% solid fiberglass that is approximately 3/8”-1/2” thick! See similar questions...

Three shortboards or two longboards is usual, to allow safe deck space. Ask first if you want to bring more. See similar questions...

The Hextile is a Nv specific protoboard designed to take advantage of various symmetries in Nv circuitry with tons of spare pads for additional circuitry, sensors, and mounts. The Hextile boards were made in several variations as a research tool, by and for Mark W. Tilden. Hextile boards are single sided square and hexagonal boards that come pre-arranged in sheets to provide the most convenient collections of biomech components for walkers, etc. See similar questions...

They are all three able to use the MegaSquirt-I CPU or the MegaSquirt-II daughterboard, but they are based on different versions of the circuit board. You can click on any of the headings to view an example of the product with pictures. The v2.2 board dates back several years, it's the least expensive of the currently available options, and the least developed. It's a great low budget solution that has (and still is) served many people well. The v3. See similar questions...

Everything but the main body shell of the FIA is done in-house. We built all the molds from our own plugs. All door pieces, hood and trunk lid, and inner panels are hand laid at E.R.A. Mating of the inner panels to the outside skin is also done in-house. We don't use ordinary polyester resin, either. We spend a little extra money to get low-shrink tooling resin for better long term dimensional stability. Dealer information E.R.A. has a very limited network of dealers. See similar questions...

It is an asphalt shingle consisting of a layer of fiberglass to resist rotting, warping, curling and fire and helps to seal out rain, sleet, snow and ice. Penfolds, as well as installing your new roof , we want to make sure your roof lasts for years to come. Follow these tips to achieve optimum performance from your roofing system. See similar questions...

Not necessarily. You can easily destroy the PCB so be careful. Too much heat can delaminate the PCB, burn it, and/or cause toxic fumes. Do not use too much heat. Have some patience. See similar questions...

Polychlorinated biphenyls (PCBs) were used in electrical transformers manufactured between 1929 and 1977, with the majority being installed in residential and commercial buildings and industrial facilities prior to 1978. A “PCB transformer” is a transformer that is known, or assumed under TSCA, to contain PCBs at concentrations greater than 500 parts per million (ppm). See similar questions...

Generally, a transformer will have a nameplate attached to the unit indicating the name of the dielectric fluid, the approximate weight in pounds, and the amount of fluid, usually in gallons. In accordance with the Toxic Substance Control Act (40 C.F.R. ? 761.40 (a)), proper PCB identification labels must be visible near the access to the transformers and also on the transformer itself. See similar questions...

Probably not the same board in low quantities for a low price. The PCB has 4 layers with solder mask, hot air leveling finish and component print. Each has been electrically tested against the Gerber data. However, it is possible, to create a 2 layer PCB from the schematics, which may be cheaper. If you want to do that or if you need a specific layout or different board dimensions, then you can download the original CAD files from the download area. The layout has been done with Eagle 4. See similar questions...

Sometimes I will do the PCB layout; especially on small boards. Usually depends if my main subcontractor is busy. See similar questions...

Not to my knowledge. The local mills (and all commercial development of local forest products) were shut down years ago by rumors of a Mexican Spotted Owl passing through the region. I understand there may still be a sawmill operating out in Eager, by Springerville, but you'd probably have to check with someone in the White Mountain region. See similar questions...

Meta BoyChat is a board set up to discuss the functioning, running, or administrating of BoyChat. If you have any questions or comments about the operation of BC itself, this is where you should post. The Treehouse is a board specifically set up for one sentence posts, posts of few words resembling back-and-forth real-time chat, or jokes and one-liners. Other Chat is a board for all off-topic or non-BL related posts. See similar questions...

Screaming Circuits does manage PCB fabrication for our customers. However, we do not do PCB fabrication internally. We have relationships with companies around the world who do PCB fabrication. See our PCB Fabrication Page. See similar questions...

If you need your water cut on, simply contact the water billing office at 989-3055. If you need your water cut off , call the same office and ask to have a final reading for your meter. See similar questions...

You can go anywhere to get your hair cut as long as the donation guidelines listed on our website are followed. We encourage our donors to go to a salon they are already familiar with so they will be comfortable when making their donation. View Donation Guidelines. See similar questions...

In short, the final version of the finished film. Although it may receive a small edit here or there in the next few weeks, the film is essentially "locked" into this form. See similar questions...