The compiler calculates the value for the SPBRG register based on the HSER_BAUD define statement, and it assumes that the BRGH bit in the TXSTA register is low. For many of the PICmicro MCU devices, baud rates greater than 2400 with a 4MHz clock result in a low SPBRG value which, in turn, causes a high baud rate error. To correct this, you should set SPBRG and the BRGH bit (TXSTA.4) explicitly with defines. The following defines will allow you to use 9600 baud with a 4MHz clock at less than 0.

No. The modem circuit in the KPC-3 Plus is only for 1200 baud. To do any higher baud rates over the radio, use one of our other TNC models such as the KPC-9612 Plus or KAM XL. Higher baud rates can only be done through a radio with the proper internal connections and bandwidth. For example, 9600 baud requires that the audio bandwidth of the radio channel be at least 5 to 8 KHz. See similar questions...

The pixel (clock) rate to read each pixel depends on the screen resolution and the vertical refresh rate (mostly fixed at about 60 Hz). See similar questions...

If you are using an ARM CrossConnect or a Wiggler you can alter the clock frequency by setting the JTAG Clock Divider target property (the default setting is 1). If you are using an ARM CrossConnect you can also enable adaptive clocking by setting the Adaptive Clocking target property to Yes. This mode uses the RTCK signal to dynamically control the JTAG clock frequency If you are using a J-Link you can alter the clock frequency by setting the Speed target property (the default setting is 4000). See similar questions...

There are many different commands for different situations. To get a list of topics that you can get help on, do 'help topics'. A few commands are also explained in the 'gameinfo' text at the login prompt. See similar questions...

Each A/D conversion needs 76 AD clocks which is selected by ADCS1and ADCS0. Please refer to the table: See similar questions...

My cats use the toilet twice a day, once for each need. They often do the two in a short interval. A cat that is feed always at the same time of day will be a lot more regular that one who eats all day. See similar questions...

Yes! Squeezebox can play daily alarms with music of your choice. Additionally, Squeezebox can connect to SqueezeNework to provide an alarm clock to wake you with your choice of compatible Internet radio stations and over 80 environmental and musical sounds. See similar questions...

Click on the gold satellite button located on the far right of the Toolbar. If an update is available it will proceed to download. The blue progress bar will indicate that you are receiving the Live Update information. After, you can check the updated version number by clicking on the Help tab and then clicking on About, which will show you the version number of your software. Make sure to use the Live Update feature often as we are always updating the MX Editor software. See similar questions...

Unfortunately there is no set standard for SSI commands that all server vendors adhere to. What this means that there are a core few commands that will work on most servers, and a number of additional commands that will only work on certain brands of server. You should check your hosts FAQs or check the documentation for your server (see below) for an absolute list of commands that will work for you. See similar questions...

petition [description] -Sends in an idea or suggestion Example: /petition I would love to see the friends list hold more names. timer -Shows a timer for a tourney you are entered in. Enter tourney, highlight it, and type /timer in the lobby. Then when you go to a slot, or game, the timer will show in the upper right corner, telling you how long till that tourney. afk -Use this command to place an "afk" (away from keyboard), by your name to let others know you are away. See similar questions...

Linux is an open source operating system similar to Unix. The following are some useful commands along with their DOS equivalent where applicable. service network restart = shut down Ethernet ports and start up again with any changes, can also just start or stop instead of restart Depending on your current path, sometimes a ./ or . is needed before a command, for instance stop, start, and restart or any filename.sh script files. See similar questions...

No. And before you ask, "Why not?", because you can screw up the entire screen and it's not implemented in the Java code. See similar questions...

There are a variety of factors that can contribute to occasional slow download speeds or time-outs. One thing that you can rule out is lack of bandwidth directly into the facility where your site is located. If it seems that your site generally is always slow, it may be because you have images on your pages that are too large. A rule of thumb is to try to make images 20k or less. If you have larger images, try using image compression software which you can download free at www.download.com. See similar questions...

Yes. You will learn using Data Commands in the following instances. To work with stored procedures that return a result set, which can be manipulated. And to access data that is not appropriate for storing in a dataset, such as data with a short life cycle. To access read-only data, that is, data that will not be updated. See similar questions...

Type the command At the command shell prompt of the Telnet client. Make sure that you are not located in the Telnet Server installation directory (where the program telnetd.exe resides). Don't confuse the program telnetd.exe with the telnetd monitoring commands. The telnetd monitoring commands can be executed as described under the question " How do I use the monitoring commands". A common mistake is to run the telnetd.exe with "parameters", such as status. See similar questions...

The important point is that only new phones supports direct flow-controlled connection between PC and phone. Because my adapters are intended for phones without handshaking, those phones you cannot operate them directly with the serial port. You need software that converts AT-commands to vendor-specific protocol. For example, Nokia Data Suite is a program for that. See similar questions...

Guide Dogs do not read the lights nor make the decision to cross the street. It is the guide dog user that gives the command to go forward. First the guide dog user listens for the traffic. When the guide dog user determines it is safe to go forward, they give the command and cross the street. If the guide dog determines it is unsafe to cross the street when it is given the command, it will "intelligently disobey". See similar questions...