There are products which are available upon request to wash and seal in one day. However, we choose a two-day method: Wash on the first day, and sand and seal the second dry day.

That depends on our climate. Decks in the direct sunlight tend to fade and dry out; decks in humid and shady areas grow algae and fungus spores. Both problems require attention yearly, or no later than two seasons apart. See similar questions...

We need a minimum 50 degree temperature to safely let deck preservative products cure and dry properly. See similar questions...

A Yes, although there is generally no need to do this. That's because the fibre used in the design is non-porous and therefore doesn't absorb the everyday dirt, grime and smells that human hair does. See similar questions...

This mainly will depend on the weather. On average a Pressure Treated Pine deck can be sealed in approximately 45-60 days from installation. A Cedar or Redwood deck can be sealed within 21 days. If you have a fair amount of rain you will need extra time for drying the wood out. Essentially you are making sure you don't seal in any moisture as this will promote rotting from the inside out. See similar questions...

This primarily comes into play if your deck is well above ground (4' or higher). The answer is no. The reason you are sealing your deck is to prevent the sun from aging the wood and more importantly, to prevent rain from rotting your deck. Since the understructure never receives any real sunlight and gravity dictates that water will not stay on the underside, it is not necessary to seal that. See similar questions...

Yes. If you elect not to seal your deck it will age prematurely and will not last as long as a properly maintained deck. A properly maintained deck in our climate should last 30 years. for what type of sealer, we highly recommend to use cost as an indicator. There are definitely reasons why a gallon of Brand X costs $15.00 while Brand Y costs $40.00. Lower cost doesn't necessarily mean better value but it definitely could mean lower performance. See similar questions...

We recommend you let your deck dry for a minimum of four weeks after construction of your deck before we apply a penetrating sealer. The problem with new wood is that the grains are closed and the wood still contains natural chemicals called tannins and mill glaze. If left to nature, it would take 3-6 months for the grain to open and the natural chemicals to leach out. By using a combination of powerwashing and mill glaze remover, we can speed up this process. See similar questions...

Most sealers need a minimum of 4-8 hours to dry, although this can vary depending on the weather and the condition of your deck. If it rains soon after we apply the sealer, look for water spots. These are lighter discolorations on the wood similar to water marks left on fine furniture. If your deck has water spots, please contact us immediately to have the sealer re-applied. See similar questions...

No, most of the logo of the seal are hot stamped or printed in paper label, so the seal are not prepared for washing. And the string of the seal is not dyed for washing as well. If you want the seal to be wash. We have to specially design and make for you. So you have to state out your wash resistance requirement for your seal in the very beginning when you make the enquiry on the seal. See similar questions...

No, if you have a lot of dirt or mud on your driveway, we suggest that you hose it off yourself the night before. We will use a heavy-duty broom to remove dirt and debris. If you have a problem with run off that has left a large area with dirt or mud, we will ask you to hose it off the night before. See similar questions...

Yes, it actually works just fine. Your house is going to get wet when we wash it, so there is little difference to rain. We will reschedule if there is danger involved, such as lightning. See similar questions...

Commercial roofs can be sealed with an Elastomeric coating applied directly to the concrete cover. Rubber Membranes can Steel Rib systems can also be applied directly. More conventional finishes (such as residential shingles) can be installed over furring strips which are anchored directly to the concrete cover. Always follow the manufacturer's instructions for proper applications. See similar questions...

Hand wash in warm or cold soapy water and AIR DRY. You can also machine wash warm or cold with your regular detergent, preferably in a laundry bag so they do not inadvertently get placed in the dryer-AIR Dry ONLY. Wash frequently (depending on use) to keep the insole free of dirt/grime and also to keep bacteria/odor free. See similar questions...

Many people still believe that acne is caused by dirty skin. The truth is, washing alone will not clear up or prevent acne. Washing does, however, help remove excess surface oils and dead skin cells. Many people use all kinds of products, including alcohol-based cleansers, and scrub vigorously, only to irritate the skin further and worsen their acne. Washing the skin twice a day gently with water and a mild soap is usually all that is required. See similar questions...