A. Monolithic installation requires that each tile be laid in the same direction to create the appearance of a uniform, whole floorcovering. See similar questions...

Monolithic Panels are prefabricated Three Dimensional Lightweight Structural panels consisting of a super-insulated polystyrene core sandwiched between two engineered layers of 10 ga Steel welded wire fabric mesh. To complete the panel form process a 10 ga Steel wire truss is pierced completely through the polystyrene core and welded to each of the outer layer sheets of 10 ga Steel welded wire fabric mesh. See similar questions...

No. However, if you don't want Wine as a dependency, you can bundle your private version of Wine into your package (.rpm/.deb). Wine has good support for such a setup via the WINEPREFIX environment variable. See similar questions...

Monolithic Three Dimensional panel meets the CABO one and two-story family dwelling codes (Compliance Report No. NER-454, 1/01/1993) which satisfies all SBCCI, ICBO and BOCA requirements for standard buildings. NES - National Evaluation Service, Inc. (NEF 454) Miami-Dade County Building Code Compliance Office American Society for Testing and Materials American National Standards Institute copies of the above reports available upon request. See similar questions...

Monolithic Panels has the following fire-resistance ratings; Fire-rating is derived from the wire mesh gauge in combination with concrete thickness. The E P S insulation core demonstrated a flame - spread index of 25 or less and a smoke developed rating of 450 or less when tested in accordance with ASTM -E84. The modified polystyrene core does not contain ozone-damaging chlorofluorocarbons (CFC's) in the manufacturing process or products. 2.5" EPS-Core with 1. See similar questions...

The rebar is embedded within the concrete slab. The panel is placed over the rebar, through the open space between the polystyrene core and the wire mesh. Once set the rebar is fastened directly to the wire mesh by hand with tie wire. See similar questions...

A bond beam is used to create large openings, or to strengthen large areas of ceiling or to he support roof structures. All bond beams created should be pre approved by a certified engineering firm. Removing the polystyrene core and installing rebar creates the bond beam. The best method for removing the polystyrene core is a high-pressure water blaster; it takes only a matter of minutes. For further information please see instruction manual. See similar questions...

Diodes, Inc. manufactures its dual transistor products using separate die which are wire bonded to the lead frames. They are not monolithic devices. See similar questions...

Answer: Monolithic slabs are foundation systems constructed as one single concrete pour consisting of typically a 4 inch thick concrete slab with interior thickened portions under load bearing walls and thickened at all perimeter edges. See similar questions...

The brief synopsis, which follows, is from the test results report dated 1994 from Dade County Miami Florida pertaining to the wind load capacity of Monolithic Panels. Three typical Monolithic Panels 4' wide and 10' tall with 1" of field applied shotcrete on each face were installed vertically, side-by-side on a concrete slab, several inches in front of a rigid backup wall with space between the panels and the backup wall. See similar questions...

The load bearing weights that a typical Monolithic Panels wall will support is amazing. The typical wood frame and metal frame wall cannot compare to Monolithic Panels strength. A typical Monolithic Panels Panel with 2.5" polystyrene core using eleven-gauge wire, 8' in height has been tested at a structure load of over 78,000 Ibs. full load bearing chart available upon request. See similar questions...

We have an online management interface that you can use to modify all the information relating to your domain name (such as contact information and nameservers). It is available here. Bear in mind you'll need your domain's username and password to make the desired changes. If you don't have a username and password or have forgotten them, please contact support. Yes. You can always use our management interface to change your nameservers to those of a new hosting company. See similar questions...

R-Value is a rating of the material resistance to thermal penetration. The higher the number, the better the protection value. Many circumstances change the R-Value rating. R-Values changes with different thickness and density of the polystyrene panel core, as Well as various thickness of shotcrete applied to the interior and exterior as well as fluctuation of ambient temperatures Chart shown below shows the minimum R-Value Ratings you can expect to use. See similar questions...

You can build curved or radius walls by cutting the eleven gauge wires on one side of the panel. This will allow the panel to bend to the desired shape or radius. It is very important not to cut through the heavier nine-gauge truss wire so that wall strength and integrity remain intact. See similar questions...

Monolithic Panels excelled in rigorous test given by Mother Nature. For the last ten years, numerous homes have been constructed with the Monolithic Building System on the East Coast, Caribbean and Gulf areas of Mexico and the United States. The homes were built to withstand hurricane fore winds. In Laboratory testing, the Monolithic Panels have been tested for up to wind loads of 226 miles per hour. See similar questions...

The shotcrete is field applied either by hand or machine application on both sides of the panel. This part of the operation is very specialized. We recommend a reputable Stucco Contractor or a combination of both Contractors for this part of the operation depending upon the desired finish. For architects with a special finish in mind we would like to mention that the architectural molds or metal trim could be incorporated into your design to achieve the desired finish. See similar questions...

A.- With cancer: It is most important to eat the seeds. The seeds must be chewed and kept in the mouth for as long as it takes for them to practically liquify. One or two seeds per hour is what should be eaten when you have cancer. The best results have come when the person eats 3-5 seeds per waking hour. Vitamin B17 is water soluble and non-toxic. It is as safe as sugar or salt. Some people get nauseous if they take too many seeds at one time. See similar questions...